{"title":"Spares And Repairs","description":"\u003cp\u003eMost LED failures are the driver, not the LED. Rather than replace a whole fitting, replace the part that failed — drivers, gaskets, lenses, demister pads and touch-up paint. Cheaper for you, and it keeps a working light out of the skip.\u003c\/p\u003e","products":[{"product_id":"trailing-edge-dimmer-for-led-lighting","title":"Trailing Edge Dimmer for LED Lighting","description":"\u003cp\u003eThe part that decides whether the light behaves: a dimmer with a 5 to 250W range and an adjustable minimum, which is the setting that stops LEDs flickering at the bottom of the dial.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here\u003c\/li\u003e\n\u003cli\u003eIP rating: IP20. No water protection at all. This is a dry area product and it must not be installed in any bathroom zone. We stock it because plenty of cloakrooms have no bath or shower in them, and we say so plainly rather than letting somebody find out\u003c\/li\u003e\n\u003cli\u003eDimensions: standard back box or a driver case, and the case dimensions are on the drawing\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable, this is a control or a supply\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable to a control. It is the driver quality that decides whether the fitting it feeds flickers, which is why we sell drivers as a named part rather than as a mystery inside a box\u003c\/li\u003e\n\u003cli\u003eDimming: trailing edge, 5 to 250W, with an adjustable minimum\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2 unless stated. Every driver here is a named part with a datasheet, and it is stocked as a spare for ten years\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 61347 for the driver, BS EN 61558-2-6 for the transformer, BS EN 60669 for the switch, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.30 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003ePosition: a driver or a transformer must be accessible for maintenance. A driver sealed into a plasterboard void is a future ceiling repair\u003c\/li\u003e\n\u003cli\u003eHeadroom: size a driver at 80 per cent of its rating. A driver run at its limit runs hot and a hot driver is a short driver\u003c\/li\u003e\n\u003cli\u003eCompatibility: tell us what fittings you are running and we will confirm the combination before you order\u003c\/li\u003e\n\u003cli\u003eZone: controls and drivers go outside the zones unless they are specifically rated, and most are not\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe item\u003c\/li\u003e\n\u003cli\u003ea datasheet with the part number\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003cli\u003eterminal screws and a gland where needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. Put the driver somewhere you can reach it again. That single decision is the difference between a ten minute repair and a ceiling.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eNearly every complaint about LED lighting is a driver complaint. Flicker at low brightness, a step at 15 per cent, a buzz on the dimmer, lights that come on at different times: all driver. So we sell drivers as named parts with datasheets and part numbers, we stock them for ten years, and we will confirm a dimmer and driver combination before you order rather than after you have wired it in.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023170212222,"sku":"BBM-DRV-001-X1","price":41.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Trailing_Edge_Dimmer_for_LED_Lighting.jpg?v=1789239875"},{"product_id":"trailing-edge-dimmer-with-a-two-way-function","title":"Trailing Edge Dimmer with a Two Way Function","description":"\u003cp\u003eThe part that decides whether the light behaves: the same dimmer wired at two positions, for a bathroom with a door at each end.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here\u003c\/li\u003e\n\u003cli\u003eIP rating: IP20. No water protection at all. This is a dry area product and it must not be installed in any bathroom zone. We stock it because plenty of cloakrooms have no bath or shower in them, and we say so plainly rather than letting somebody find out\u003c\/li\u003e\n\u003cli\u003eDimensions: standard back box or a driver case, and the case dimensions are on the drawing\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable, this is a control or a supply\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable to a control. It is the driver quality that decides whether the fitting it feeds flickers, which is why we sell drivers as a named part rather than as a mystery inside a box\u003c\/li\u003e\n\u003cli\u003eDimming: trailing edge, 5 to 250W, with an adjustable minimum\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2 unless stated. Every driver here is a named part with a datasheet, and it is stocked as a spare for ten years\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 61347 for the driver, BS EN 61558-2-6 for the transformer, BS EN 60669 for the switch, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.35 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003ePosition: a driver or a transformer must be accessible for maintenance. A driver sealed into a plasterboard void is a future ceiling repair\u003c\/li\u003e\n\u003cli\u003eHeadroom: size a driver at 80 per cent of its rating. A driver run at its limit runs hot and a hot driver is a short driver\u003c\/li\u003e\n\u003cli\u003eCompatibility: tell us what fittings you are running and we will confirm the combination before you order\u003c\/li\u003e\n\u003cli\u003eZone: controls and drivers go outside the zones unless they are specifically rated, and most are not\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe item\u003c\/li\u003e\n\u003cli\u003ea datasheet with the part number\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003cli\u003eterminal screws and a gland where needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. Put the driver somewhere you can reach it again. That single decision is the difference between a ten minute repair and a ceiling.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eNearly every complaint about LED lighting is a driver complaint. Flicker at low brightness, a step at 15 per cent, a buzz on the dimmer, lights that come on at different times: all driver. So we sell drivers as named parts with datasheets and part numbers, we stock them for ten years, and we will confirm a dimmer and driver combination before you order rather than after you have wired it in.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023170244990,"sku":"BBM-DRV-002-X1","price":59.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Trailing_Edge_Dimmer_with_a_Two_Way_Function.jpg?v=1789239877"},{"product_id":"rotary-dimmer-with-an-adjustable-minimum","title":"Rotary Dimmer with an Adjustable Minimum","description":"\u003cp\u003eThe part that decides whether the light behaves: a screwdriver trim for the minimum, which is how you tune out the drop out point of whatever drivers you actually have.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here\u003c\/li\u003e\n\u003cli\u003eIP rating: IP20. No water protection at all. This is a dry area product and it must not be installed in any bathroom zone. We stock it because plenty of cloakrooms have no bath or shower in them, and we say so plainly rather than letting somebody find out\u003c\/li\u003e\n\u003cli\u003eDimensions: standard back box or a driver case, and the case dimensions are on the drawing\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable, this is a control or a supply\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable to a control. It is the driver quality that decides whether the fitting it feeds flickers, which is why we sell drivers as a named part rather than as a mystery inside a box\u003c\/li\u003e\n\u003cli\u003eDimming: trailing edge, 5 to 250W, with an adjustable minimum\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2 unless stated. Every driver here is a named part with a datasheet, and it is stocked as a spare for ten years\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 61347 for the driver, BS EN 61558-2-6 for the transformer, BS EN 60669 for the switch, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.30 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003ePosition: a driver or a transformer must be accessible for maintenance. A driver sealed into a plasterboard void is a future ceiling repair\u003c\/li\u003e\n\u003cli\u003eHeadroom: size a driver at 80 per cent of its rating. A driver run at its limit runs hot and a hot driver is a short driver\u003c\/li\u003e\n\u003cli\u003eCompatibility: tell us what fittings you are running and we will confirm the combination before you order\u003c\/li\u003e\n\u003cli\u003eZone: controls and drivers go outside the zones unless they are specifically rated, and most are not\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe item\u003c\/li\u003e\n\u003cli\u003ea datasheet with the part number\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003cli\u003eterminal screws and a gland where needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. Put the driver somewhere you can reach it again. That single decision is the difference between a ten minute repair and a ceiling.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eNearly every complaint about LED lighting is a driver complaint. Flicker at low brightness, a step at 15 per cent, a buzz on the dimmer, lights that come on at different times: all driver. So we sell drivers as named parts with datasheets and part numbers, we stock them for ten years, and we will confirm a dimmer and driver combination before you order rather than after you have wired it in.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023170277758,"sku":"BBM-DRV-003-X1","price":49.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Rotary_Dimmer_with_an_Adjustable_Minimum.jpg?v=1789239866"},{"product_id":"selv-transformer-for-zone-0-lighting","title":"SELV Transformer for Zone 0 Lighting","description":"\u003cp\u003eThe part that decides whether the light behaves: a 12 volt transformer to be sited outside the zones, which is what makes a zone 0 fitting lawful.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here\u003c\/li\u003e\n\u003cli\u003eIP rating: IP20. No water protection at all. This is a dry area product and it must not be installed in any bathroom zone. We stock it because plenty of cloakrooms have no bath or shower in them, and we say so plainly rather than letting somebody find out\u003c\/li\u003e\n\u003cli\u003eDimensions: standard back box or a driver case, and the case dimensions are on the drawing\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable, this is a control or a supply\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable to a control. It is the driver quality that decides whether the fitting it feeds flickers, which is why we sell drivers as a named part rather than as a mystery inside a box\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2 unless stated. Every driver here is a named part with a datasheet, and it is stocked as a spare for ten years\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 61347 for the driver, BS EN 61558-2-6 for the transformer, BS EN 60669 for the switch, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.90 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003ePosition: a driver or a transformer must be accessible for maintenance. A driver sealed into a plasterboard void is a future ceiling repair\u003c\/li\u003e\n\u003cli\u003eHeadroom: size a driver at 80 per cent of its rating. A driver run at its limit runs hot and a hot driver is a short driver\u003c\/li\u003e\n\u003cli\u003eCompatibility: tell us what fittings you are running and we will confirm the combination before you order\u003c\/li\u003e\n\u003cli\u003eZone: controls and drivers go outside the zones unless they are specifically rated, and most are not\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe item\u003c\/li\u003e\n\u003cli\u003ea datasheet with the part number\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003cli\u003eterminal screws and a gland where needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. Put the driver somewhere you can reach it again. That single decision is the difference between a ten minute repair and a ceiling.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eNearly every complaint about LED lighting is a driver complaint. Flicker at low brightness, a step at 15 per cent, a buzz on the dimmer, lights that come on at different times: all driver. So we sell drivers as named parts with datasheets and part numbers, we stock them for ten years, and we will confirm a dimmer and driver combination before you order rather than after you have wired it in.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023170310526,"sku":"BBM-DRV-004-X1","price":79.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/SELV_Transformer_for_Zone_0_Lighting.jpg?v=1789239864"},{"product_id":"constant-current-led-driver-at-350ma","title":"Constant Current LED Driver at 350mA","description":"\u003cp\u003eThe part that decides whether the light behaves: a replacement driver, because a driver is the part that fails and a fitting is not.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here\u003c\/li\u003e\n\u003cli\u003eIP rating: IP20. No water protection at all. This is a dry area product and it must not be installed in any bathroom zone. We stock it because plenty of cloakrooms have no bath or shower in them, and we say so plainly rather than letting somebody find out\u003c\/li\u003e\n\u003cli\u003eDimensions: standard back box or a driver case, and the case dimensions are on the drawing\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable, this is a control or a supply\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable to a control. It is the driver quality that decides whether the fitting it feeds flickers, which is why we sell drivers as a named part rather than as a mystery inside a box\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2 unless stated. Every driver here is a named part with a datasheet, and it is stocked as a spare for ten years\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 61347 for the driver, BS EN 61558-2-6 for the transformer, BS EN 60669 for the switch, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.25 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003ePosition: a driver or a transformer must be accessible for maintenance. A driver sealed into a plasterboard void is a future ceiling repair\u003c\/li\u003e\n\u003cli\u003eHeadroom: size a driver at 80 per cent of its rating. A driver run at its limit runs hot and a hot driver is a short driver\u003c\/li\u003e\n\u003cli\u003eCompatibility: tell us what fittings you are running and we will confirm the combination before you order\u003c\/li\u003e\n\u003cli\u003eZone: controls and drivers go outside the zones unless they are specifically rated, and most are not\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe item\u003c\/li\u003e\n\u003cli\u003ea datasheet with the part number\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003cli\u003eterminal screws and a gland where needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. Put the driver somewhere you can reach it again. That single decision is the difference between a ten minute repair and a ceiling.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eNearly every complaint about LED lighting is a driver complaint. Flicker at low brightness, a step at 15 per cent, a buzz on the dimmer, lights that come on at different times: all driver. So we sell drivers as named parts with datasheets and part numbers, we stock them for ten years, and we will confirm a dimmer and driver combination before you order rather than after you have wired it in.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023170343294,"sku":"BBM-DRV-005-X1","price":31.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Constant_Current_LED_Driver_at_350mA.jpg?v=1789239654"},{"product_id":"constant-voltage-led-driver-at-24v-and-60w","title":"Constant Voltage LED Driver at 24V and 60W","description":"\u003cp\u003eThe part that decides whether the light behaves: for a tape run, sized with 20 per cent headroom, which is the rule that decides whether a driver lasts three years or ten.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here\u003c\/li\u003e\n\u003cli\u003eIP rating: IP20. No water protection at all. This is a dry area product and it must not be installed in any bathroom zone. We stock it because plenty of cloakrooms have no bath or shower in them, and we say so plainly rather than letting somebody find out\u003c\/li\u003e\n\u003cli\u003eDimensions: standard back box or a driver case, and the case dimensions are on the drawing\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable, this is a control or a supply\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable to a control. It is the driver quality that decides whether the fitting it feeds flickers, which is why we sell drivers as a named part rather than as a mystery inside a box\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2 unless stated. Every driver here is a named part with a datasheet, and it is stocked as a spare for ten years\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 61347 for the driver, BS EN 61558-2-6 for the transformer, BS EN 60669 for the switch, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.40 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003ePosition: a driver or a transformer must be accessible for maintenance. A driver sealed into a plasterboard void is a future ceiling repair\u003c\/li\u003e\n\u003cli\u003eHeadroom: size a driver at 80 per cent of its rating. A driver run at its limit runs hot and a hot driver is a short driver\u003c\/li\u003e\n\u003cli\u003eCompatibility: tell us what fittings you are running and we will confirm the combination before you order\u003c\/li\u003e\n\u003cli\u003eZone: controls and drivers go outside the zones unless they are specifically rated, and most are not\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe item\u003c\/li\u003e\n\u003cli\u003ea datasheet with the part number\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003cli\u003eterminal screws and a gland where needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. Put the driver somewhere you can reach it again. That single decision is the difference between a ten minute repair and a ceiling.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eNearly every complaint about LED lighting is a driver complaint. Flicker at low brightness, a step at 15 per cent, a buzz on the dimmer, lights that come on at different times: all driver. So we sell drivers as named parts with datasheets and part numbers, we stock them for ten years, and we will confirm a dimmer and driver combination before you order rather than after you have wired it in.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023170376062,"sku":"BBM-DRV-006-X1","price":45.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Constant_Voltage_LED_Driver_at_24V_and_60W.jpg?v=1789239653"},{"product_id":"ip67-led-driver-for-a-wet-location","title":"IP67 LED Driver for a Wet Location","description":"\u003cp\u003eThe part that decides whether the light behaves: a potted driver that can live in a damp void, for the situations where there is nowhere dry to put one.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here\u003c\/li\u003e\n\u003cli\u003eIP rating: IP67. Dust tight and protected against temporary immersion in up to a metre of water, which is what zone 0 requires and what a fitting in a shower tray or a bath surround has to be\u003c\/li\u003e\n\u003cli\u003eDimensions: standard back box or a driver case, and the case dimensions are on the drawing\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable, this is a control or a supply\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable to a control. It is the driver quality that decides whether the fitting it feeds flickers, which is why we sell drivers as a named part rather than as a mystery inside a box\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2 unless stated. Every driver here is a named part with a datasheet, and it is stocked as a spare for ten years\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 61347 for the driver, BS EN 61558-2-6 for the transformer, BS EN 60669 for the switch, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.60 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003ePosition: a driver or a transformer must be accessible for maintenance. A driver sealed into a plasterboard void is a future ceiling repair\u003c\/li\u003e\n\u003cli\u003eHeadroom: size a driver at 80 per cent of its rating. A driver run at its limit runs hot and a hot driver is a short driver\u003c\/li\u003e\n\u003cli\u003eCompatibility: tell us what fittings you are running and we will confirm the combination before you order\u003c\/li\u003e\n\u003cli\u003eZone: controls and drivers go outside the zones unless they are specifically rated, and most are not\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe item\u003c\/li\u003e\n\u003cli\u003ea datasheet with the part number\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003cli\u003eterminal screws and a gland where needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. Put the driver somewhere you can reach it again. That single decision is the difference between a ten minute repair and a ceiling.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eNearly every complaint about LED lighting is a driver complaint. Flicker at low brightness, a step at 15 per cent, a buzz on the dimmer, lights that come on at different times: all driver. So we sell drivers as named parts with datasheets and part numbers, we stock them for ten years, and we will confirm a dimmer and driver combination before you order rather than after you have wired it in.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023170408830,"sku":"BBM-DRV-007-X1","price":69.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP67_LED_Driver_for_a_Wet_Location.jpg?v=1789239869"},{"product_id":"dali-2-led-driver","title":"DALI 2 LED Driver","description":"\u003cp\u003eThe part that decides whether the light behaves: an addressable driver for a commissioned scheme.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here\u003c\/li\u003e\n\u003cli\u003eIP rating: IP20. No water protection at all. This is a dry area product and it must not be installed in any bathroom zone. We stock it because plenty of cloakrooms have no bath or shower in them, and we say so plainly rather than letting somebody find out\u003c\/li\u003e\n\u003cli\u003eDimensions: standard back box or a driver case, and the case dimensions are on the drawing\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable, this is a control or a supply\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable to a control. It is the driver quality that decides whether the fitting it feeds flickers, which is why we sell drivers as a named part rather than as a mystery inside a box\u003c\/li\u003e\n\u003cli\u003eDimming: DALI 2\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2 unless stated. Every driver here is a named part with a datasheet, and it is stocked as a spare for ten years\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 61347 for the driver, BS EN 61558-2-6 for the transformer, BS EN 60669 for the switch, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.40 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003ePosition: a driver or a transformer must be accessible for maintenance. A driver sealed into a plasterboard void is a future ceiling repair\u003c\/li\u003e\n\u003cli\u003eHeadroom: size a driver at 80 per cent of its rating. A driver run at its limit runs hot and a hot driver is a short driver\u003c\/li\u003e\n\u003cli\u003eCompatibility: tell us what fittings you are running and we will confirm the combination before you order\u003c\/li\u003e\n\u003cli\u003eZone: controls and drivers go outside the zones unless they are specifically rated, and most are not\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe item\u003c\/li\u003e\n\u003cli\u003ea datasheet with the part number\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003cli\u003eterminal screws and a gland where needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. Put the driver somewhere you can reach it again. That single decision is the difference between a ten minute repair and a ceiling.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eNearly every complaint about LED lighting is a driver complaint. Flicker at low brightness, a step at 15 per cent, a buzz on the dimmer, lights that come on at different times: all driver. So we sell drivers as named parts with datasheets and part numbers, we stock them for ten years, and we will confirm a dimmer and driver combination before you order rather than after you have wired it in.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023170441598,"sku":"BBM-DRV-008-X1","price":79.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/DALI_2_LED_Driver.jpg?v=1789239656"},{"product_id":"pull-cord-switch-in-a-ceiling-rose","title":"Pull Cord Switch in a Ceiling Rose","description":"\u003cp\u003eThe part that decides whether the light behaves: a 6 amp cord switch, which is the switch a bathroom may have inside it.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: standard back box or a driver case, and the case dimensions are on the drawing\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable, this is a control or a supply\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable to a control. It is the driver quality that decides whether the fitting it feeds flickers, which is why we sell drivers as a named part rather than as a mystery inside a box\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2 unless stated. Every driver here is a named part with a datasheet, and it is stocked as a spare for ten years\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 61347 for the driver, BS EN 61558-2-6 for the transformer, BS EN 60669 for the switch, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.20 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003ePosition: a driver or a transformer must be accessible for maintenance. A driver sealed into a plasterboard void is a future ceiling repair\u003c\/li\u003e\n\u003cli\u003eHeadroom: size a driver at 80 per cent of its rating. A driver run at its limit runs hot and a hot driver is a short driver\u003c\/li\u003e\n\u003cli\u003eCompatibility: tell us what fittings you are running and we will confirm the combination before you order\u003c\/li\u003e\n\u003cli\u003eZone: controls and drivers go outside the zones unless they are specifically rated, and most are not\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe item\u003c\/li\u003e\n\u003cli\u003ea datasheet with the part number\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003cli\u003eterminal screws and a gland where needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. Put the driver somewhere you can reach it again. That single decision is the difference between a ten minute repair and a ceiling.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eNearly every complaint about LED lighting is a driver complaint. Flicker at low brightness, a step at 15 per cent, a buzz on the dimmer, lights that come on at different times: all driver. So we sell drivers as named parts with datasheets and part numbers, we stock them for ten years, and we will confirm a dimmer and driver combination before you order rather than after you have wired it in.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023170539902,"sku":"BBM-DRV-011-X1","price":27.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Pull_Cord_Switch_in_a_Ceiling_Rose.jpg?v=1789239862"},{"product_id":"silicone-gasket-set-for-ip65-downlights","title":"Silicone Gasket Set for IP65 Downlights","description":"\u003cp\u003eA spare part: the gaskets perish long before the fitting does, and a perished gasket is an IP20 fitting in a zone 1 position.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here, except where the part is itself rated, which is stated on the pack\u003c\/li\u003e\n\u003cli\u003eIP rating: stated on the pack for every sealed part. A gasket or a connector carries the rating of the assembly it completes, which is why a perished gasket takes a zone 1 fitting out of compliance\u003c\/li\u003e\n\u003cli\u003eDimensions: as described, and the pack quantity is in the title where it matters\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable to a part\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: not applicable unless the part carries a current, and where it does the rating is on the pack\u003c\/li\u003e\n\u003cli\u003eFire rating: stated on the pack. The fire hood is tested to BS 476 Part 21 for 30, 60 and 90 minutes\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 where the part forms a luminaire, BS EN 60529 for the IP rated parts, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.10 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: two years\u003c\/li\u003e\n\u003cli\u003eAvailability: every part is stocked for ten years from the date a fitting is discontinued\u003c\/li\u003e\n\u003cli\u003eCompatibility: send us a photograph of the part you are replacing and we will confirm before you order\u003c\/li\u003e\n\u003cli\u003eWhy we list these: a bathroom fitting is a sealed assembly and the seal is the consumable. Selling gaskets is cheaper for you than selling fittings and it is the reason people come back\u003c\/li\u003e\n\u003cli\u003eTrade: available on account, and we will put a spares kit together for a specific job\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe parts as described\u003c\/li\u003e\n\u003cli\u003einstructions where fitting is not obvious\u003c\/li\u003e\n\u003cli\u003ethe pack rating card where the part is IP rated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eFollow the instructions on the pack. On any gasket, the surface under it has to be clean and dry, because a gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAn IP rating is a property of an assembly, not of a fitting, and the part that expires is the gasket. A ten year old IP65 downlight with a hardened gasket is not IP65 any more, and it is sitting above a shower. Replacing gaskets is a twenty minute job and about eighteen pounds, and nobody in this trade tells you to do it because there is no money in it. We stock them anyway.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023171195262,"sku":"BBM-SPR-001-X1","price":17.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Silicone_Gasket_Set_for_IP65_Downlights.jpg?v=1789239877"},{"product_id":"ip68-gel-filled-connector-pack","title":"IP68 Gel Filled Connector Pack","description":"\u003cp\u003eA spare part: gel filled crimps for a connection in a damp void, which is the only kind that should be made there.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here, except where the part is itself rated, which is stated on the pack\u003c\/li\u003e\n\u003cli\u003eIP rating: stated on the pack for every sealed part. A gasket or a connector carries the rating of the assembly it completes, which is why a perished gasket takes a zone 1 fitting out of compliance\u003c\/li\u003e\n\u003cli\u003eDimensions: as described, and the pack quantity is in the title where it matters\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable to a part\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: not applicable unless the part carries a current, and where it does the rating is on the pack\u003c\/li\u003e\n\u003cli\u003eFire rating: stated on the pack. The fire hood is tested to BS 476 Part 21 for 30, 60 and 90 minutes\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 where the part forms a luminaire, BS EN 60529 for the IP rated parts, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.15 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: two years\u003c\/li\u003e\n\u003cli\u003eAvailability: every part is stocked for ten years from the date a fitting is discontinued\u003c\/li\u003e\n\u003cli\u003eCompatibility: send us a photograph of the part you are replacing and we will confirm before you order\u003c\/li\u003e\n\u003cli\u003eWhy we list these: a bathroom fitting is a sealed assembly and the seal is the consumable. Selling gaskets is cheaper for you than selling fittings and it is the reason people come back\u003c\/li\u003e\n\u003cli\u003eTrade: available on account, and we will put a spares kit together for a specific job\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe parts as described\u003c\/li\u003e\n\u003cli\u003einstructions where fitting is not obvious\u003c\/li\u003e\n\u003cli\u003ethe pack rating card where the part is IP rated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eFollow the instructions on the pack. On any gasket, the surface under it has to be clean and dry, because a gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAn IP rating is a property of an assembly, not of a fitting, and the part that expires is the gasket. A ten year old IP65 downlight with a hardened gasket is not IP65 any more, and it is sitting above a shower. Replacing gaskets is a twenty minute job and about eighteen pounds, and nobody in this trade tells you to do it because there is no money in it. We stock them anyway.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023171228030,"sku":"BBM-SPR-002-X1","price":21.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP68_Gel_Filled_Connector_Pack.jpg?v=1789239864"},{"product_id":"ip65-push-fit-connector-pack","title":"IP65 Push Fit Connector Pack","description":"\u003cp\u003eA spare part: sealed push fit connectors for downlight tails, in a pack of ten.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here, except where the part is itself rated, which is stated on the pack\u003c\/li\u003e\n\u003cli\u003eIP rating: stated on the pack for every sealed part. A gasket or a connector carries the rating of the assembly it completes, which is why a perished gasket takes a zone 1 fitting out of compliance\u003c\/li\u003e\n\u003cli\u003eDimensions: as described, and the pack quantity is in the title where it matters\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable to a part\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: not applicable unless the part carries a current, and where it does the rating is on the pack\u003c\/li\u003e\n\u003cli\u003eFire rating: stated on the pack. The fire hood is tested to BS 476 Part 21 for 30, 60 and 90 minutes\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 where the part forms a luminaire, BS EN 60529 for the IP rated parts, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.10 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: two years\u003c\/li\u003e\n\u003cli\u003eAvailability: every part is stocked for ten years from the date a fitting is discontinued\u003c\/li\u003e\n\u003cli\u003eCompatibility: send us a photograph of the part you are replacing and we will confirm before you order\u003c\/li\u003e\n\u003cli\u003eWhy we list these: a bathroom fitting is a sealed assembly and the seal is the consumable. Selling gaskets is cheaper for you than selling fittings and it is the reason people come back\u003c\/li\u003e\n\u003cli\u003eTrade: available on account, and we will put a spares kit together for a specific job\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe parts as described\u003c\/li\u003e\n\u003cli\u003einstructions where fitting is not obvious\u003c\/li\u003e\n\u003cli\u003ethe pack rating card where the part is IP rated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eFollow the instructions on the pack. On any gasket, the surface under it has to be clean and dry, because a gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAn IP rating is a property of an assembly, not of a fitting, and the part that expires is the gasket. A ten year old IP65 downlight with a hardened gasket is not IP65 any more, and it is sitting above a shower. Replacing gaskets is a twenty minute job and about eighteen pounds, and nobody in this trade tells you to do it because there is no money in it. We stock them anyway.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023171260798,"sku":"BBM-SPR-003-X1","price":15.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP65_Push_Fit_Connector_Pack.jpg?v=1789239813"},{"product_id":"downlight-cut-out-template-set","title":"Downlight Cut Out Template Set","description":"\u003cp\u003eA spare part: templates for 65, 68, 75 and 85mm cut outs, which saves one wrong hole and has therefore already paid for itself.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here, except where the part is itself rated, which is stated on the pack\u003c\/li\u003e\n\u003cli\u003eIP rating: stated on the pack for every sealed part. A gasket or a connector carries the rating of the assembly it completes, which is why a perished gasket takes a zone 1 fitting out of compliance\u003c\/li\u003e\n\u003cli\u003eDimensions: as described, and the pack quantity is in the title where it matters\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable to a part\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: not applicable unless the part carries a current, and where it does the rating is on the pack\u003c\/li\u003e\n\u003cli\u003eFire rating: stated on the pack. The fire hood is tested to BS 476 Part 21 for 30, 60 and 90 minutes\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 where the part forms a luminaire, BS EN 60529 for the IP rated parts, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.05 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: two years\u003c\/li\u003e\n\u003cli\u003eAvailability: every part is stocked for ten years from the date a fitting is discontinued\u003c\/li\u003e\n\u003cli\u003eCompatibility: send us a photograph of the part you are replacing and we will confirm before you order\u003c\/li\u003e\n\u003cli\u003eWhy we list these: a bathroom fitting is a sealed assembly and the seal is the consumable. Selling gaskets is cheaper for you than selling fittings and it is the reason people come back\u003c\/li\u003e\n\u003cli\u003eTrade: available on account, and we will put a spares kit together for a specific job\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe parts as described\u003c\/li\u003e\n\u003cli\u003einstructions where fitting is not obvious\u003c\/li\u003e\n\u003cli\u003ethe pack rating card where the part is IP rated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eFollow the instructions on the pack. On any gasket, the surface under it has to be clean and dry, because a gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAn IP rating is a property of an assembly, not of a fitting, and the part that expires is the gasket. A ten year old IP65 downlight with a hardened gasket is not IP65 any more, and it is sitting above a shower. Replacing gaskets is a twenty minute job and about eighteen pounds, and nobody in this trade tells you to do it because there is no money in it. We stock them anyway.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023171293566,"sku":"BBM-SPR-004-X1","price":8.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Downlight_Cut_Out_Template_Set.jpg?v=1789239633"},{"product_id":"fire-hood-for-a-non-rated-downlight","title":"Fire Hood for a Non Rated Downlight","description":"\u003cp\u003eA spare part: for the fittings already in a ceiling that should not be there, which is a great many of them.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here, except where the part is itself rated, which is stated on the pack\u003c\/li\u003e\n\u003cli\u003eIP rating: stated on the pack for every sealed part. A gasket or a connector carries the rating of the assembly it completes, which is why a perished gasket takes a zone 1 fitting out of compliance\u003c\/li\u003e\n\u003cli\u003eDimensions: as described, and the pack quantity is in the title where it matters\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable to a part\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: not applicable unless the part carries a current, and where it does the rating is on the pack\u003c\/li\u003e\n\u003cli\u003eFire rating: stated on the pack. The fire hood is tested to BS 476 Part 21 for 30, 60 and 90 minutes\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 where the part forms a luminaire, BS EN 60529 for the IP rated parts, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.40 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: two years\u003c\/li\u003e\n\u003cli\u003eAvailability: every part is stocked for ten years from the date a fitting is discontinued\u003c\/li\u003e\n\u003cli\u003eCompatibility: send us a photograph of the part you are replacing and we will confirm before you order\u003c\/li\u003e\n\u003cli\u003eWhy we list these: a bathroom fitting is a sealed assembly and the seal is the consumable. Selling gaskets is cheaper for you than selling fittings and it is the reason people come back\u003c\/li\u003e\n\u003cli\u003eTrade: available on account, and we will put a spares kit together for a specific job\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe parts as described\u003c\/li\u003e\n\u003cli\u003einstructions where fitting is not obvious\u003c\/li\u003e\n\u003cli\u003ethe pack rating card where the part is IP rated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eFollow the instructions on the pack. On any gasket, the surface under it has to be clean and dry, because a gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAn IP rating is a property of an assembly, not of a fitting, and the part that expires is the gasket. A ten year old IP65 downlight with a hardened gasket is not IP65 any more, and it is sitting above a shower. Replacing gaskets is a twenty minute job and about eighteen pounds, and nobody in this trade tells you to do it because there is no money in it. We stock them anyway.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023171326334,"sku":"BBM-SPR-005-X1","price":23.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Fire_Hood_for_a_Non_Rated_Downlight.jpg?v=1789239637"},{"product_id":"tile-fixing-set-for-wall-lights","title":"Tile Fixing Set for Wall Lights","description":"\u003cp\u003eA spare part: a tile bit and plugs sized for a 6mm hole through tile into plasterboard without cracking the tile.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here, except where the part is itself rated, which is stated on the pack\u003c\/li\u003e\n\u003cli\u003eIP rating: stated on the pack for every sealed part. A gasket or a connector carries the rating of the assembly it completes, which is why a perished gasket takes a zone 1 fitting out of compliance\u003c\/li\u003e\n\u003cli\u003eDimensions: as described, and the pack quantity is in the title where it matters\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable to a part\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: not applicable unless the part carries a current, and where it does the rating is on the pack\u003c\/li\u003e\n\u003cli\u003eFire rating: stated on the pack. The fire hood is tested to BS 476 Part 21 for 30, 60 and 90 minutes\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 where the part forms a luminaire, BS EN 60529 for the IP rated parts, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.15 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: two years\u003c\/li\u003e\n\u003cli\u003eAvailability: every part is stocked for ten years from the date a fitting is discontinued\u003c\/li\u003e\n\u003cli\u003eCompatibility: send us a photograph of the part you are replacing and we will confirm before you order\u003c\/li\u003e\n\u003cli\u003eWhy we list these: a bathroom fitting is a sealed assembly and the seal is the consumable. Selling gaskets is cheaper for you than selling fittings and it is the reason people come back\u003c\/li\u003e\n\u003cli\u003eTrade: available on account, and we will put a spares kit together for a specific job\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe parts as described\u003c\/li\u003e\n\u003cli\u003einstructions where fitting is not obvious\u003c\/li\u003e\n\u003cli\u003ethe pack rating card where the part is IP rated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eFollow the instructions on the pack. On any gasket, the surface under it has to be clean and dry, because a gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAn IP rating is a property of an assembly, not of a fitting, and the part that expires is the gasket. A ten year old IP65 downlight with a hardened gasket is not IP65 any more, and it is sitting above a shower. Replacing gaskets is a twenty minute job and about eighteen pounds, and nobody in this trade tells you to do it because there is no money in it. We stock them anyway.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023171359102,"sku":"BBM-SPR-006-X1","price":13.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Tile_Fixing_Set_for_Wall_Lights.jpg?v=1789239875"},{"product_id":"mirror-mounting-bracket-set","title":"Mirror Mounting Bracket Set","description":"\u003cp\u003eA spare part: brackets with a levelling screw, for hanging a mirror straight on a wall that is not.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here, except where the part is itself rated, which is stated on the pack\u003c\/li\u003e\n\u003cli\u003eIP rating: stated on the pack for every sealed part. A gasket or a connector carries the rating of the assembly it completes, which is why a perished gasket takes a zone 1 fitting out of compliance\u003c\/li\u003e\n\u003cli\u003eDimensions: as described, and the pack quantity is in the title where it matters\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable to a part\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: not applicable unless the part carries a current, and where it does the rating is on the pack\u003c\/li\u003e\n\u003cli\u003eFire rating: stated on the pack. The fire hood is tested to BS 476 Part 21 for 30, 60 and 90 minutes\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 where the part forms a luminaire, BS EN 60529 for the IP rated parts, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.50 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: two years\u003c\/li\u003e\n\u003cli\u003eAvailability: every part is stocked for ten years from the date a fitting is discontinued\u003c\/li\u003e\n\u003cli\u003eCompatibility: send us a photograph of the part you are replacing and we will confirm before you order\u003c\/li\u003e\n\u003cli\u003eWhy we list these: a bathroom fitting is a sealed assembly and the seal is the consumable. Selling gaskets is cheaper for you than selling fittings and it is the reason people come back\u003c\/li\u003e\n\u003cli\u003eTrade: available on account, and we will put a spares kit together for a specific job\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe parts as described\u003c\/li\u003e\n\u003cli\u003einstructions where fitting is not obvious\u003c\/li\u003e\n\u003cli\u003ethe pack rating card where the part is IP rated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eFollow the instructions on the pack. On any gasket, the surface under it has to be clean and dry, because a gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAn IP rating is a property of an assembly, not of a fitting, and the part that expires is the gasket. A ten year old IP65 downlight with a hardened gasket is not IP65 any more, and it is sitting above a shower. Replacing gaskets is a twenty minute job and about eighteen pounds, and nobody in this trade tells you to do it because there is no money in it. We stock them anyway.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023171391870,"sku":"BBM-SPR-007-X1","price":27.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Mirror_Mounting_Bracket_Set.jpg?v=1789239867"},{"product_id":"tile-vent-for-a-bathroom-extract-duct","title":"Tile Vent for a Bathroom Extract Duct","description":"\u003cp\u003eA spare part: the correct termination for a fan duct through a tiled roof, which is where a fan should end and often does not.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here, except where the part is itself rated, which is stated on the pack\u003c\/li\u003e\n\u003cli\u003eIP rating: stated on the pack for every sealed part. A gasket or a connector carries the rating of the assembly it completes, which is why a perished gasket takes a zone 1 fitting out of compliance\u003c\/li\u003e\n\u003cli\u003eDimensions: as described, and the pack quantity is in the title where it matters\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable to a part\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: not applicable unless the part carries a current, and where it does the rating is on the pack\u003c\/li\u003e\n\u003cli\u003eFire rating: stated on the pack. The fire hood is tested to BS 476 Part 21 for 30, 60 and 90 minutes\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 where the part forms a luminaire, BS EN 60529 for the IP rated parts, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.80 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: two years\u003c\/li\u003e\n\u003cli\u003eAvailability: every part is stocked for ten years from the date a fitting is discontinued\u003c\/li\u003e\n\u003cli\u003eCompatibility: send us a photograph of the part you are replacing and we will confirm before you order\u003c\/li\u003e\n\u003cli\u003eWhy we list these: a bathroom fitting is a sealed assembly and the seal is the consumable. Selling gaskets is cheaper for you than selling fittings and it is the reason people come back\u003c\/li\u003e\n\u003cli\u003eTrade: available on account, and we will put a spares kit together for a specific job\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe parts as described\u003c\/li\u003e\n\u003cli\u003einstructions where fitting is not obvious\u003c\/li\u003e\n\u003cli\u003ethe pack rating card where the part is IP rated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eFollow the instructions on the pack. On any gasket, the surface under it has to be clean and dry, because a gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAn IP rating is a property of an assembly, not of a fitting, and the part that expires is the gasket. A ten year old IP65 downlight with a hardened gasket is not IP65 any more, and it is sitting above a shower. Replacing gaskets is a twenty minute job and about eighteen pounds, and nobody in this trade tells you to do it because there is no money in it. We stock them anyway.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023171457406,"sku":"BBM-SPR-009-X1","price":33.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Tile_Vent_for_a_Bathroom_Extract_Duct.jpg?v=1789239874"},{"product_id":"rigid-duct-kit-at-100mm","title":"Rigid Duct Kit at 100mm","description":"\u003cp\u003eA spare part: three metres of rigid duct, two bends and clamps, because flexible duct halves an extract rate.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here, except where the part is itself rated, which is stated on the pack\u003c\/li\u003e\n\u003cli\u003eIP rating: stated on the pack for every sealed part. A gasket or a connector carries the rating of the assembly it completes, which is why a perished gasket takes a zone 1 fitting out of compliance\u003c\/li\u003e\n\u003cli\u003eDimensions: as described, and the pack quantity is in the title where it matters\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable to a part\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: not applicable unless the part carries a current, and where it does the rating is on the pack\u003c\/li\u003e\n\u003cli\u003eFire rating: stated on the pack. The fire hood is tested to BS 476 Part 21 for 30, 60 and 90 minutes\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 where the part forms a luminaire, BS EN 60529 for the IP rated parts, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 1.20 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: two years\u003c\/li\u003e\n\u003cli\u003eAvailability: every part is stocked for ten years from the date a fitting is discontinued\u003c\/li\u003e\n\u003cli\u003eCompatibility: send us a photograph of the part you are replacing and we will confirm before you order\u003c\/li\u003e\n\u003cli\u003eWhy we list these: a bathroom fitting is a sealed assembly and the seal is the consumable. Selling gaskets is cheaper for you than selling fittings and it is the reason people come back\u003c\/li\u003e\n\u003cli\u003eTrade: available on account, and we will put a spares kit together for a specific job\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe parts as described\u003c\/li\u003e\n\u003cli\u003einstructions where fitting is not obvious\u003c\/li\u003e\n\u003cli\u003ethe pack rating card where the part is IP rated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eFollow the instructions on the pack. On any gasket, the surface under it has to be clean and dry, because a gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAn IP rating is a property of an assembly, not of a fitting, and the part that expires is the gasket. A ten year old IP65 downlight with a hardened gasket is not IP65 any more, and it is sitting above a shower. Replacing gaskets is a twenty minute job and about eighteen pounds, and nobody in this trade tells you to do it because there is no money in it. We stock them anyway.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023171490174,"sku":"BBM-SPR-010-X1","price":37.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Rigid_Duct_Kit_at_100mm.jpg?v=1789239872"},{"product_id":"backdraught-shutter-for-a-100mm-duct","title":"Backdraught Shutter for a 100mm Duct","description":"\u003cp\u003eA spare part: stops the cold coming back down the duct, which is the reason a bathroom is cold in January.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here, except where the part is itself rated, which is stated on the pack\u003c\/li\u003e\n\u003cli\u003eIP rating: stated on the pack for every sealed part. A gasket or a connector carries the rating of the assembly it completes, which is why a perished gasket takes a zone 1 fitting out of compliance\u003c\/li\u003e\n\u003cli\u003eDimensions: as described, and the pack quantity is in the title where it matters\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable to a part\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: not applicable unless the part carries a current, and where it does the rating is on the pack\u003c\/li\u003e\n\u003cli\u003eFire rating: stated on the pack. The fire hood is tested to BS 476 Part 21 for 30, 60 and 90 minutes\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 where the part forms a luminaire, BS EN 60529 for the IP rated parts, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.20 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: two years\u003c\/li\u003e\n\u003cli\u003eAvailability: every part is stocked for ten years from the date a fitting is discontinued\u003c\/li\u003e\n\u003cli\u003eCompatibility: send us a photograph of the part you are replacing and we will confirm before you order\u003c\/li\u003e\n\u003cli\u003eWhy we list these: a bathroom fitting is a sealed assembly and the seal is the consumable. Selling gaskets is cheaper for you than selling fittings and it is the reason people come back\u003c\/li\u003e\n\u003cli\u003eTrade: available on account, and we will put a spares kit together for a specific job\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe parts as described\u003c\/li\u003e\n\u003cli\u003einstructions where fitting is not obvious\u003c\/li\u003e\n\u003cli\u003ethe pack rating card where the part is IP rated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eFollow the instructions on the pack. On any gasket, the surface under it has to be clean and dry, because a gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAn IP rating is a property of an assembly, not of a fitting, and the part that expires is the gasket. A ten year old IP65 downlight with a hardened gasket is not IP65 any more, and it is sitting above a shower. Replacing gaskets is a twenty minute job and about eighteen pounds, and nobody in this trade tells you to do it because there is no money in it. We stock them anyway.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023171522942,"sku":"BBM-SPR-011-X1","price":17.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Backdraught_Shutter_for_a_100mm_Duct.jpg?v=1789239641"},{"product_id":"replacement-glass-lens-for-an-ip65-downlight","title":"Replacement Glass Lens for an IP65 Downlight","description":"\u003cp\u003eA spare part: the tempered lens, which gets dropped during a lamp change more often than anything else in this shop.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: outside the zones only, which means more than 600mm from the edge of a bath or shower and more than 600mm from a basin tap. We would still fit an IP44 product in a bathroom, and this one is, but the regulations do not require it here, except where the part is itself rated, which is stated on the pack\u003c\/li\u003e\n\u003cli\u003eIP rating: stated on the pack for every sealed part. A gasket or a connector carries the rating of the assembly it completes, which is why a perished gasket takes a zone 1 fitting out of compliance\u003c\/li\u003e\n\u003cli\u003eDimensions: as described, and the pack quantity is in the title where it matters\u003c\/li\u003e\n\u003cli\u003eLight output: not applicable to a part\u003c\/li\u003e\n\u003cli\u003eColour temperature: not applicable\u003c\/li\u003e\n\u003cli\u003eColour rendering: not applicable\u003c\/li\u003e\n\u003cli\u003eDimming: not applicable\u003c\/li\u003e\n\u003cli\u003eElectrical: not applicable unless the part carries a current, and where it does the rating is on the pack\u003c\/li\u003e\n\u003cli\u003eFire rating: stated on the pack. The fire hood is tested to BS 476 Part 21 for 30, 60 and 90 minutes\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 where the part forms a luminaire, BS EN 60529 for the IP rated parts, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.08 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: two years\u003c\/li\u003e\n\u003cli\u003eAvailability: every part is stocked for ten years from the date a fitting is discontinued\u003c\/li\u003e\n\u003cli\u003eCompatibility: send us a photograph of the part you are replacing and we will confirm before you order\u003c\/li\u003e\n\u003cli\u003eWhy we list these: a bathroom fitting is a sealed assembly and the seal is the consumable. Selling gaskets is cheaper for you than selling fittings and it is the reason people come back\u003c\/li\u003e\n\u003cli\u003eTrade: available on account, and we will put a spares kit together for a specific job\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe parts as described\u003c\/li\u003e\n\u003cli\u003einstructions where fitting is not obvious\u003c\/li\u003e\n\u003cli\u003ethe pack rating card where the part is IP rated\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eFollow the instructions on the pack. On any gasket, the surface under it has to be clean and dry, because a gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAn IP rating is a property of an assembly, not of a fitting, and the part that expires is the gasket. A ten year old IP65 downlight with a hardened gasket is not IP65 any more, and it is sitting above a shower. Replacing gaskets is a twenty minute job and about eighteen pounds, and nobody in this trade tells you to do it because there is no money in it. We stock them anyway.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"One","offer_id":58023171588478,"sku":"BBM-SPR-013-X1","price":13.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Replacement_Glass_Lens_for_an_IP65_Downlight.jpg?v=1789239864"}],"url":"https:\/\/batheandbeam.com\/collections\/spares.oembed","provider":"Bathe \u0026 Beam","version":"1.0","type":"link"}