{"title":"Brushed Chrome","description":"\u003cp\u003eThe most forgiving finish in a bathroom: it hides water marks and fingerprints in a way polished chrome never will, and it matches most UK tapware.\u003c\/p\u003e","products":[{"product_id":"complete-bathroom-lighting-scheme-in-brushed-chrome","title":"Complete Bathroom Lighting Scheme in Brushed Chrome","description":"\u003cp\u003eA complete scheme: six IP65 downlights, a mirror light, a shaver socket and the drivers and dimmer to run them, specified as one circuit rather than bought as seven separate guesses.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 6 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 3900 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 9.4 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023065977214,"sku":"BBM-SCH-002-R8","price":1224.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023066009982,"sku":"BBM-SCH-002-R4","price":1024.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023066042750,"sku":"BBM-SCH-002-R14","price":1599.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Complete_Bathroom_Lighting_Scheme_in_Brushed_Chrome.jpg?v=1789239659"},{"product_id":"bathroom-lighting-scheme-with-a-demisting-mirror-in-brushed-chrome","title":"Bathroom Lighting Scheme with a Demisting Mirror in Brushed Chrome","description":"\u003cp\u003eA complete scheme: the same scheme with a front lit demisting mirror in place of the mirror light, which is the version most people actually want once they understand the difference.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 6 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 3900 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 21.4 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023069679998,"sku":"BBM-SCH-006-R8","price":1649.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023069712766,"sku":"BBM-SCH-006-R4","price":1374.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023069745534,"sku":"BBM-SCH-006-R14","price":2124.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Bathroom_Lighting_Scheme_with_a_Demisting_Mirror_in_Brushed_Chrome.jpg?v=1789239660"},{"product_id":"bathroom-lighting-scheme-with-a-mirror-cabinet-in-brushed-chrome","title":"Bathroom Lighting Scheme with a Mirror Cabinet in Brushed Chrome","description":"\u003cp\u003eA complete scheme: the scheme built around an illuminated mirror cabinet, so the storage and the task light are the same purchase.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 6 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 3900 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 28.6 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023073251710,"sku":"BBM-SCH-010-R8","price":1849.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023073284478,"sku":"BBM-SCH-010-R4","price":1549.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023073317246,"sku":"BBM-SCH-010-R14","price":2399.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Bathroom_Lighting_Scheme_with_a_Mirror_Cabinet_in_Brushed_Chrome.jpg?v=1789239657"},{"product_id":"en-suite-lighting-scheme-in-brushed-chrome","title":"En Suite Lighting Scheme in Brushed Chrome","description":"\u003cp\u003eA complete scheme: four downlights, a mirror light and a shaver socket, sized for a room under four square metres where six downlights would be glare rather than light.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 4 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 2600 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 7.2 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e4 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023078232446,"sku":"BBM-SCH-014-R8","price":1124.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023078265214,"sku":"BBM-SCH-014-R4","price":949.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023078297982,"sku":"BBM-SCH-014-R14","price":1474.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/En_Suite_Lighting_Scheme_in_Brushed_Chrome.jpg?v=1789239653"},{"product_id":"bathroom-lighting-scheme-with-layered-light-in-brushed-chrome","title":"Bathroom Lighting Scheme with Layered Light in Brushed Chrome","description":"\u003cp\u003eA complete scheme: three circuits rather than one: downlights for cleaning, a mirror light for the face and a low level night circuit, which is the arrangement that stops a bathroom being a surgery at two in the morning.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 6 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 3900 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 12.8 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: three, on separate switches\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023081673086,"sku":"BBM-SCH-018-R8","price":1749.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023081705854,"sku":"BBM-SCH-018-R4","price":1474.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023081738622,"sku":"BBM-SCH-018-R14","price":2274.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Bathroom_Lighting_Scheme_with_Layered_Light_in_Brushed_Chrome.jpg?v=1789239655"},{"product_id":"bathroom-lighting-scheme-with-a-night-circuit-in-brushed-chrome","title":"Bathroom Lighting Scheme with a Night Circuit in Brushed Chrome","description":"\u003cp\u003eA complete scheme: the standard scheme plus a floor level circuit on its own switch at 1 lux, so nobody has to turn the main light on at three in the morning.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 6 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 3900 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 10.6 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: two, with the night circuit on its own switch\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023086358910,"sku":"BBM-SCH-022-R8","price":1424.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023086391678,"sku":"BBM-SCH-022-R4","price":1199.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023086424446,"sku":"BBM-SCH-022-R14","price":1874.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Bathroom_Lighting_Scheme_with_a_Night_Circuit_in_Brushed_Chrome.jpg?v=1789239635"},{"product_id":"bathroom-lighting-scheme-with-fire-rated-downlights-in-brushed-chrome","title":"Bathroom Lighting Scheme with Fire Rated Downlights in Brushed Chrome","description":"\u003cp\u003eA complete scheme: the scheme with fire rated downlights throughout, which is what a flat or the ceiling below a habitable room actually requires.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 6 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 3900 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 11.8 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023089308030,"sku":"BBM-SCH-026-R8","price":1499.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023089340798,"sku":"BBM-SCH-026-R4","price":1249.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023089373566,"sku":"BBM-SCH-026-R14","price":1924.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Bathroom_Lighting_Scheme_with_Fire_Rated_Downlights_in_Brushed_Chrome.jpg?v=1789239635"},{"product_id":"bathroom-lighting-scheme-with-a-feature-pendant-in-brushed-chrome","title":"Bathroom Lighting Scheme with a Feature Pendant in Brushed Chrome","description":"\u003cp\u003eA complete scheme: a scheme built around an IP44 rated pendant over the bath, with the downlights taking a supporting role rather than doing all the work.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 6 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 3900 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 14.2 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023095337342,"sku":"BBM-SCH-030-R8","price":1949.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023095370110,"sku":"BBM-SCH-030-R4","price":1649.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023095402878,"sku":"BBM-SCH-030-R14","price":2524.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Bathroom_Lighting_Scheme_with_a_Feature_Pendant_in_Brushed_Chrome.jpg?v=1789239658"},{"product_id":"bathroom-lighting-scheme-with-cove-lighting-in-brushed-chrome","title":"Bathroom Lighting Scheme with Cove Lighting in Brushed Chrome","description":"\u003cp\u003eA complete scheme: an IP65 tape run in a cove or a shadow gap, with the downlights and the mirror light specified around it and every driver sized with 20 per cent headroom.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 6 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 3900 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 16.4 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023099531646,"sku":"BBM-SCH-034-R8","price":2149.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023099564414,"sku":"BBM-SCH-034-R4","price":1824.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023099597182,"sku":"BBM-SCH-034-R14","price":2799.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Bathroom_Lighting_Scheme_with_Cove_Lighting_in_Brushed_Chrome.jpg?v=1789239657"},{"product_id":"bathroom-lighting-scheme-for-a-high-ceiling-in-brushed-chrome","title":"Bathroom Lighting Scheme for a High Ceiling in Brushed Chrome","description":"\u003cp\u003eA complete scheme: eight downlights with a narrower beam angle, because a 45 degree beam from a three metre ceiling lands as pools and gaps rather than as light.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 8 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 5200 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 13.6 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e8 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023104315774,"sku":"BBM-SCH-038-R8","price":1849.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023104348542,"sku":"BBM-SCH-038-R4","price":1549.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023104381310,"sku":"BBM-SCH-038-R14","price":2399.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Bathroom_Lighting_Scheme_for_a_High_Ceiling_in_Brushed_Chrome.jpg?v=1789239656"},{"product_id":"bathroom-lighting-scheme-with-an-extractor-fan-in-brushed-chrome","title":"Bathroom Lighting Scheme with an Extractor Fan in Brushed Chrome","description":"\u003cp\u003eA complete scheme: the fan and the lights specified together with the fan on an overrun timer and the extract rate matched to the room volume, which is what building regulations ask for and almost nobody calculates.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 6 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 3900 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 14.8 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023110148478,"sku":"BBM-SCH-042-R8","price":1599.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023110181246,"sku":"BBM-SCH-042-R4","price":1324.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023110214014,"sku":"BBM-SCH-042-R14","price":2074.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Bathroom_Lighting_Scheme_with_an_Extractor_Fan_in_Brushed_Chrome.jpg?v=1789239660"},{"product_id":"bathroom-lighting-scheme-with-a-tunable-mirror-light-in-brushed-chrome","title":"Bathroom Lighting Scheme with a Tunable Mirror Light in Brushed Chrome","description":"\u003cp\u003eA complete scheme: a mirror light that runs 2700K in the evening and 5000K in the morning, which is the one place in a house where a tunable fitting is worth the money.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 6 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 3900 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 12.2 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023113949566,"sku":"BBM-SCH-046-R8","price":1799.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023113982334,"sku":"BBM-SCH-046-R4","price":1499.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023114015102,"sku":"BBM-SCH-046-R14","price":2324.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Bathroom_Lighting_Scheme_with_a_Tunable_Mirror_Light_in_Brushed_Chrome.jpg?v=1789239659"},{"product_id":"family-bathroom-scheme-with-dimming-throughout-in-brushed-chrome","title":"Family Bathroom Scheme with Dimming Throughout in Brushed Chrome","description":"\u003cp\u003eA complete scheme: every circuit on a trailing edge dimmer with drivers chosen to dim smoothly to 1 per cent, because most LED bathroom fittings step out at 15 per cent and flicker on the way.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 6 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 3900 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 13.4 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023117947262,"sku":"BBM-SCH-050-R8","price":1899.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023117980030,"sku":"BBM-SCH-050-R4","price":1599.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023118012798,"sku":"BBM-SCH-050-R14","price":2474.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Family_Bathroom_Scheme_with_Dimming_Throughout_in_Brushed_Chrome.jpg?v=1789239654"},{"product_id":"cloakroom-lighting-scheme-in-brushed-chrome","title":"Cloakroom Lighting Scheme in Brushed Chrome","description":"\u003cp\u003eA complete scheme: three downlights and a mirror light for a cloakroom, where there is usually no bath or shower and therefore no zone at all, which changes what you may fit.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower. Every fitting in this scheme that can go in zone 1 is IP65 and the ones that cannot are marked in the pack list\u003c\/li\u003e\n\u003cli\u003eDimensions: 3 downlights at 85mm cut out, plus the mirror light and the accessories listed below\u003c\/li\u003e\n\u003cli\u003eLight output: 1950 lumens total at 88 lumens per circuit watt, which meets the Part L figure of 75 with headroom\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above, and the whole scheme is supplied at one colour temperature because a bathroom with two whites in it looks like a mistake\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable on a trailing edge dimmer, supplied, and every driver in the scheme is from the same family so they dim together rather than in steps\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: not fire rated. If the ceiling below is a fire compartment, which it is in a flat and in most two storey extensions, this fitting needs a fire hood or a different product\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.4 kilograms for the whole scheme\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eScheme drawing: a reflected ceiling plan showing every fitting position dimensioned from the walls, supplied as a PDF with the order\u003c\/li\u003e\n\u003cli\u003eCircuits: one\u003c\/li\u003e\n\u003cli\u003eSaving: about 15 per cent against the same fittings bought individually\u003c\/li\u003e\n\u003cli\u003eEfficacy: quoted in lumens per circuit watt, including driver losses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e3 IP65 downlights with integral drivers\u003c\/li\u003e\n\u003cli\u003ethe mirror light or mirror as listed\u003c\/li\u003e\n\u003cli\u003ea shaver socket to BS EN 61558-2-5\u003c\/li\u003e\n\u003cli\u003ea trailing edge dimmer matched to the drivers\u003c\/li\u003e\n\u003cli\u003eIP65 connector blocks and cable glands\u003c\/li\u003e\n\u003cli\u003ea reflected ceiling plan dimensioned to your room\u003c\/li\u003e\n\u003cli\u003ea zone drawing showing where each fitting may and may not go\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician, most of a day. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The scheme arrives with a reflected ceiling plan dimensioned from the walls rather than a suggestion to space them evenly, because evenly spaced downlights in a bathroom put a light directly over the person at the basin and none on their face.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe case for buying a scheme rather than seven fittings is not the 15 per cent. It is that the colour temperatures match, the drivers come from one family so they dim together, the total load is inside the dimmer's rating, and somebody has worked out where the fittings go relative to the basin and the bath rather than relative to the ceiling. Those four things are what make a bathroom look lit rather than illuminated, and none of them survive buying by the item.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Family bathroom of 4 to 8 square metres","offer_id":58023118438782,"sku":"BBM-SCH-054-R8","price":1074.0,"currency_code":"GBP","in_stock":true},{"title":"Cloakroom or en suite up to 4 square metres","offer_id":58023118471550,"sku":"BBM-SCH-054-R4","price":899.0,"currency_code":"GBP","in_stock":true},{"title":"Large bathroom or wet room of 8 to 14 square metres","offer_id":58023118504318,"sku":"BBM-SCH-054-R14","price":1399.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Cloakroom_Lighting_Scheme_in_Brushed_Chrome.jpg?v=1789239651"},{"product_id":"marine-grade-wet-room-lighting-package-in-brushed-chrome","title":"Marine Grade Wet Room Lighting Package in Brushed Chrome","description":"\u003cp\u003eFor a room that is wet all day: 316 stainless throughout, because a wet room is wet all day and 304 stainless will tea stain in a couple of years.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 11.2 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eCorrosion: triple plated over brass, salt spray tested to 500 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023118700926,"sku":"BBM-WRP-001-27","price":1649.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023118733694,"sku":"BBM-WRP-001-30","price":1649.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023118766462,"sku":"BBM-WRP-001-40","price":1649.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Marine_Grade_Wet_Room_Lighting_Package_in_Brushed_Chrome.jpg?v=1789239864"},{"product_id":"wet-room-lighting-package-with-zone-0-floor-lights-in-brushed-chrome","title":"Wet Room Lighting Package with Zone 0 Floor Lights in Brushed Chrome","description":"\u003cp\u003eFor a room that is wet all day: IP67 SELV floor lights inside the shower area itself, running at 12 volts with the transformer outside the zones, which is the only lawful way to put a light there.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 0, which is inside the bath or the shower tray itself. A fitting here must be IP67 and must run at SELV, meaning 12 volts or less with the transformer outside the zones\u003c\/li\u003e\n\u003cli\u003eIP rating: IP67. Dust tight and protected against temporary immersion in up to a metre of water, which is what zone 0 requires and what a fitting in a shower tray or a bath surround has to be\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: SELV, 12 volts, with the transformer sited outside the zones. This is what makes the fitting legal in zone 0 and it is not optional\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 12.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eCorrosion: triple plated over brass, salt spray tested to 500 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023119061374,"sku":"BBM-WRP-004-27","price":1949.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023119094142,"sku":"BBM-WRP-004-30","price":1949.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023119126910,"sku":"BBM-WRP-004-40","price":1949.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wet_Room_Lighting_Package_with_Zone_0_Floor_Lights_in_Brushed_Chrome.jpg?v=1789239874"},{"product_id":"steam-room-lighting-package-in-brushed-chrome","title":"Steam Room Lighting Package in Brushed Chrome","description":"\u003cp\u003eFor a room that is wet all day: fittings rated to 60 degrees ambient with silicone gaskets rather than nitrile, because a nitrile gasket in a steam room hardens and lets water in within a season.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 14.8 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eCorrosion: triple plated over brass, salt spray tested to 500 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 60 degrees, which is a steam room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023119421822,"sku":"BBM-WRP-007-27","price":2374.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023119454590,"sku":"BBM-WRP-007-30","price":2374.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023119487358,"sku":"BBM-WRP-007-40","price":2374.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Steam_Room_Lighting_Package_in_Brushed_Chrome.jpg?v=1789239873"},{"product_id":"wet-room-package-with-coloured-mood-lighting-in-brushed-chrome","title":"Wet Room Package with Coloured Mood Lighting in Brushed Chrome","description":"\u003cp\u003eFor a room that is wet all day: an IP67 RGBW tape in the shower recess on a separate SELV driver, which is the one place colour changing light is not a gimmick.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 13.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eCorrosion: triple plated over brass, salt spray tested to 500 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023120175486,"sku":"BBM-WRP-013-27","price":2149.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023120208254,"sku":"BBM-WRP-013-30","price":2149.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023120241022,"sku":"BBM-WRP-013-40","price":2149.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wet_Room_Package_with_Coloured_Mood_Lighting_in_Brushed_Chrome.jpg?v=1789239877"},{"product_id":"wet-room-lighting-package-with-a-demisting-mirror-in-brushed-chrome","title":"Wet Room Lighting Package with a Demisting Mirror in Brushed Chrome","description":"\u003cp\u003eFor a room that is wet all day: a wet room package with a mirror rated for the humidity a wet room actually reaches, which is not the same specification as a bathroom mirror.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 26.4 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eCorrosion: triple plated over brass, salt spray tested to 500 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023120568702,"sku":"BBM-WRP-016-27","price":2249.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023120601470,"sku":"BBM-WRP-016-30","price":2249.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023120634238,"sku":"BBM-WRP-016-40","price":2249.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wet_Room_Lighting_Package_with_a_Demisting_Mirror_in_Brushed_Chrome.jpg?v=1789239875"},{"product_id":"sauna-lighting-package-in-brushed-chrome","title":"Sauna Lighting Package in Brushed Chrome","description":"\u003cp\u003eFor a room that is wet all day: fittings rated to 125 degrees with ceramic terminal blocks and no plastic in the hot zone, plus a shielded backrest light.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 12.2 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eCorrosion: triple plated over brass, salt spray tested to 500 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 125 degrees on the sauna fittings\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023120961918,"sku":"BBM-WRP-019-27","price":2049.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023120994686,"sku":"BBM-WRP-019-30","price":2049.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023121027454,"sku":"BBM-WRP-019-40","price":2049.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Sauna_Lighting_Package_in_Brushed_Chrome.jpg?v=1789239876"},{"product_id":"wet-room-package-for-a-coastal-house-in-brushed-chrome","title":"Wet Room Package for a Coastal House in Brushed Chrome","description":"\u003cp\u003eFor a room that is wet all day: 316 stainless, marine grade gaskets and a salt spray tested finish to BS EN ISO 9227, for a house within a mile of the sea where ordinary chrome pits inside two winters.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 13.8 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eCorrosion: triple plated over brass, salt spray tested to 500 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023121420670,"sku":"BBM-WRP-022-27","price":2199.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023121453438,"sku":"BBM-WRP-022-30","price":2199.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023121486206,"sku":"BBM-WRP-022-40","price":2199.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wet_Room_Package_for_a_Coastal_House_in_Brushed_Chrome.jpg?v=1789239877"},{"product_id":"wet-room-lighting-package-with-an-extract-system-in-brushed-chrome","title":"Wet Room Lighting Package with an Extract System in Brushed Chrome","description":"\u003cp\u003eFor a room that is wet all day: the lights and a continuous running extract unit specified together, sized to the room volume, because a wet room without proper extract destroys its own ceiling.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 19.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eCorrosion: triple plated over brass, salt spray tested to 500 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023121781118,"sku":"BBM-WRP-025-27","price":2299.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023121813886,"sku":"BBM-WRP-025-30","price":2299.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023121846654,"sku":"BBM-WRP-025-40","price":2299.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wet_Room_Lighting_Package_with_an_Extract_System_in_Brushed_Chrome.jpg?v=1789239875"},{"product_id":"illuminated-mirror-cabinet-with-a-demister-pad-in-brushed-chrome","title":"Illuminated Mirror Cabinet with a Demister Pad in Brushed Chrome","description":"\u003cp\u003eAn illuminated mirror cabinet: front lit at face height with a demister pad that covers the whole door rather than a postcard in the middle of it.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 145mm, and the recessed version needs a 105mm cavity\u003c\/li\u003e\n\u003cli\u003eLight output: 1450 lumens from the front lighting at 82 lumens per circuit watt, which is 320 lux at the face from 400mm and is the figure that matters\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white on the front lighting as standard, which is the right temperature for a face, with a tunable option on some models\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: not dimmable as standard. A mirror light that dims is a mirror light somebody has left on 20 per cent and then complained about\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur. Not supplied with a plug, because a plug in a bathroom is not lawful\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 26.4 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: full door coverage, 60 watts per square metre, switched with the light\u003c\/li\u003e\n\u003cli\u003eCarcass: aluminium, not MDF. An MDF bathroom cabinet swells at the bottom edge within five years and there is no repairing it\u003c\/li\u003e\n\u003cli\u003eMirror: 4mm silvered float glass, safety backed to BS EN 1036\u003c\/li\u003e\n\u003cli\u003eMounting: surface mounted on a French cleat, which is a great deal easier to get level than four screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe cabinet, assembled\u003c\/li\u003e\n\u003cli\u003ethe French cleat or the recessing frame\u003c\/li\u003e\n\u003cli\u003efixings for masonry and for stud\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe electrical connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the connection, and two people for the lift. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The cabinet hangs on a French cleat, which means you level one batten rather than four screws, and the recessed version needs its frame in before the plasterboard, so it is a decision made early or not at all.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe question that decides this purchase is where the light is. Front lit means a lit panel each side of the mirror at face height, and it is the only arrangement that lights a face evenly with no shadow under the eyes and the chin. A backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. Everything on this page is front lit, and where a model also has a backlight it is on a separate switch and described as ambient rather than as task light.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"800mm and two doors","offer_id":58023122174334,"sku":"BBM-IMC-001-C80","price":1124.0,"currency_code":"GBP","in_stock":true},{"title":"1000mm and three doors","offer_id":58023122207102,"sku":"BBM-IMC-001-C100","price":1349.0,"currency_code":"GBP","in_stock":true},{"title":"1200mm and three doors","offer_id":58023122239870,"sku":"BBM-IMC-001-C120","price":1574.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Illuminated_Mirror_Cabinet_with_a_Demister_Pad_in_Brushed_Chrome.jpg?v=1789239747"},{"product_id":"illuminated-mirror-cabinet-with-double-sided-mirrors-in-brushed-chrome","title":"Illuminated Mirror Cabinet with Double Sided Mirrors in Brushed Chrome","description":"\u003cp\u003eAn illuminated mirror cabinet: mirrored inside the doors as well as outside, which is the difference between a cabinet and a cupboard with a mirror on the front.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 145mm, and the recessed version needs a 105mm cavity\u003c\/li\u003e\n\u003cli\u003eLight output: 1450 lumens from the front lighting at 82 lumens per circuit watt, which is 320 lux at the face from 400mm and is the figure that matters\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white on the front lighting as standard, which is the right temperature for a face, with a tunable option on some models\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: not dimmable as standard. A mirror light that dims is a mirror light somebody has left on 20 per cent and then complained about\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur. Not supplied with a plug, because a plug in a bathroom is not lawful\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 29.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: not fitted on this model\u003c\/li\u003e\n\u003cli\u003eCarcass: aluminium, not MDF. An MDF bathroom cabinet swells at the bottom edge within five years and there is no repairing it\u003c\/li\u003e\n\u003cli\u003eMirror: 4mm silvered float glass, safety backed to BS EN 1036\u003c\/li\u003e\n\u003cli\u003eMounting: surface mounted on a French cleat, which is a great deal easier to get level than four screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe cabinet, assembled\u003c\/li\u003e\n\u003cli\u003ethe French cleat or the recessing frame\u003c\/li\u003e\n\u003cli\u003efixings for masonry and for stud\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe electrical connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the connection, and two people for the lift. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The cabinet hangs on a French cleat, which means you level one batten rather than four screws, and the recessed version needs its frame in before the plasterboard, so it is a decision made early or not at all.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe question that decides this purchase is where the light is. Front lit means a lit panel each side of the mirror at face height, and it is the only arrangement that lights a face evenly with no shadow under the eyes and the chin. A backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. Everything on this page is front lit, and where a model also has a backlight it is on a separate switch and described as ambient rather than as task light.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"800mm and two doors","offer_id":58023122534782,"sku":"BBM-IMC-004-C80","price":1274.0,"currency_code":"GBP","in_stock":true},{"title":"1000mm and three doors","offer_id":58023122567550,"sku":"BBM-IMC-004-C100","price":1549.0,"currency_code":"GBP","in_stock":true},{"title":"1200mm and three doors","offer_id":58023122600318,"sku":"BBM-IMC-004-C120","price":1799.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Illuminated_Mirror_Cabinet_with_Double_Sided_Mirrors_in_Brushed_Chrome.jpg?v=1789239732"},{"product_id":"illuminated-mirror-cabinet-with-a-shaver-socket-in-brushed-chrome","title":"Illuminated Mirror Cabinet with a Shaver Socket in Brushed Chrome","description":"\u003cp\u003eAn illuminated mirror cabinet: a dual voltage shaver socket to BS EN 61558-2-5 inside the cabinet, which is where it should be rather than on the wall beside it.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 145mm, and the recessed version needs a 105mm cavity\u003c\/li\u003e\n\u003cli\u003eLight output: 1450 lumens from the front lighting at 82 lumens per circuit watt, which is 320 lux at the face from 400mm and is the figure that matters\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white on the front lighting as standard, which is the right temperature for a face, with a tunable option on some models\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: not dimmable as standard. A mirror light that dims is a mirror light somebody has left on 20 per cent and then complained about\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur. Not supplied with a plug, because a plug in a bathroom is not lawful\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken, plus BS EN 61558-2-5 for the isolating transformer, which is the standard that makes a shaver socket safe in a bathroom\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 28.2 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: not fitted on this model\u003c\/li\u003e\n\u003cli\u003eCarcass: aluminium, not MDF. An MDF bathroom cabinet swells at the bottom edge within five years and there is no repairing it\u003c\/li\u003e\n\u003cli\u003eMirror: 4mm silvered float glass, safety backed to BS EN 1036\u003c\/li\u003e\n\u003cli\u003eMounting: surface mounted on a French cleat, which is a great deal easier to get level than four screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe cabinet, assembled\u003c\/li\u003e\n\u003cli\u003ethe French cleat or the recessing frame\u003c\/li\u003e\n\u003cli\u003efixings for masonry and for stud\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe electrical connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the connection, and two people for the lift. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The cabinet hangs on a French cleat, which means you level one batten rather than four screws, and the recessed version needs its frame in before the plasterboard, so it is a decision made early or not at all.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe question that decides this purchase is where the light is. Front lit means a lit panel each side of the mirror at face height, and it is the only arrangement that lights a face evenly with no shadow under the eyes and the chin. A backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. Everything on this page is front lit, and where a model also has a backlight it is on a separate switch and described as ambient rather than as task light.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"800mm and two doors","offer_id":58023122895230,"sku":"BBM-IMC-007-C80","price":1224.0,"currency_code":"GBP","in_stock":true},{"title":"1000mm and three doors","offer_id":58023122927998,"sku":"BBM-IMC-007-C100","price":1474.0,"currency_code":"GBP","in_stock":true},{"title":"1200mm and three doors","offer_id":58023122960766,"sku":"BBM-IMC-007-C120","price":1724.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Illuminated_Mirror_Cabinet_with_a_Shaver_Socket_in_Brushed_Chrome.jpg?v=1789239749"},{"product_id":"illuminated-mirror-cabinet-with-tunable-front-lighting-in-brushed-chrome","title":"Illuminated Mirror Cabinet with Tunable Front Lighting in Brushed Chrome","description":"\u003cp\u003eAn illuminated mirror cabinet: 2700K to 5000K at the front, so the mirror can be warm at night and daylight for makeup.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 145mm, and the recessed version needs a 105mm cavity\u003c\/li\u003e\n\u003cli\u003eLight output: 1450 lumens from the front lighting at 82 lumens per circuit watt, which is 320 lux at the face from 400mm and is the figure that matters\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white on the front lighting as standard, which is the right temperature for a face, with a tunable option on some models\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: not dimmable as standard. A mirror light that dims is a mirror light somebody has left on 20 per cent and then complained about\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur. Not supplied with a plug, because a plug in a bathroom is not lawful\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 29.8 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: not fitted on this model\u003c\/li\u003e\n\u003cli\u003eCarcass: aluminium, not MDF. An MDF bathroom cabinet swells at the bottom edge within five years and there is no repairing it\u003c\/li\u003e\n\u003cli\u003eMirror: 4mm silvered float glass, safety backed to BS EN 1036\u003c\/li\u003e\n\u003cli\u003eMounting: surface mounted on a French cleat, which is a great deal easier to get level than four screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe cabinet, assembled\u003c\/li\u003e\n\u003cli\u003ethe French cleat or the recessing frame\u003c\/li\u003e\n\u003cli\u003efixings for masonry and for stud\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe electrical connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the connection, and two people for the lift. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The cabinet hangs on a French cleat, which means you level one batten rather than four screws, and the recessed version needs its frame in before the plasterboard, so it is a decision made early or not at all.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe question that decides this purchase is where the light is. Front lit means a lit panel each side of the mirror at face height, and it is the only arrangement that lights a face evenly with no shadow under the eyes and the chin. A backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. Everything on this page is front lit, and where a model also has a backlight it is on a separate switch and described as ambient rather than as task light.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"800mm and two doors","offer_id":58023123386750,"sku":"BBM-IMC-010-C80","price":1499.0,"currency_code":"GBP","in_stock":true},{"title":"1000mm and three doors","offer_id":58023123419518,"sku":"BBM-IMC-010-C100","price":1774.0,"currency_code":"GBP","in_stock":true},{"title":"1200mm and three doors","offer_id":58023123452286,"sku":"BBM-IMC-010-C120","price":2074.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Illuminated_Mirror_Cabinet_with_Tunable_Front_Lighting_in_Brushed_Chrome.jpg?v=1789239737"},{"product_id":"illuminated-mirror-cabinet-with-an-ambient-backlight-in-brushed-chrome","title":"Illuminated Mirror Cabinet with an Ambient Backlight in Brushed Chrome","description":"\u003cp\u003eAn illuminated mirror cabinet: front lighting for the face and a separate backlight for the room, on two switches, because one of those jobs cannot do the other.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 145mm, and the recessed version needs a 105mm cavity\u003c\/li\u003e\n\u003cli\u003eLight output: 1450 lumens from the front lighting at 82 lumens per circuit watt, which is 320 lux at the face from 400mm and is the figure that matters\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white on the front lighting as standard, which is the right temperature for a face, with a tunable option on some models\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: not dimmable as standard. A mirror light that dims is a mirror light somebody has left on 20 per cent and then complained about\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur. Not supplied with a plug, because a plug in a bathroom is not lawful\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 30.4 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: not fitted on this model\u003c\/li\u003e\n\u003cli\u003eCarcass: aluminium, not MDF. An MDF bathroom cabinet swells at the bottom edge within five years and there is no repairing it\u003c\/li\u003e\n\u003cli\u003eMirror: 4mm silvered float glass, safety backed to BS EN 1036\u003c\/li\u003e\n\u003cli\u003eMounting: surface mounted on a French cleat, which is a great deal easier to get level than four screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe cabinet, assembled\u003c\/li\u003e\n\u003cli\u003ethe French cleat or the recessing frame\u003c\/li\u003e\n\u003cli\u003efixings for masonry and for stud\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe electrical connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the connection, and two people for the lift. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The cabinet hangs on a French cleat, which means you level one batten rather than four screws, and the recessed version needs its frame in before the plasterboard, so it is a decision made early or not at all.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe question that decides this purchase is where the light is. Front lit means a lit panel each side of the mirror at face height, and it is the only arrangement that lights a face evenly with no shadow under the eyes and the chin. A backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. Everything on this page is front lit, and where a model also has a backlight it is on a separate switch and described as ambient rather than as task light.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"800mm and two doors","offer_id":58023123943806,"sku":"BBM-IMC-013-C80","price":1374.0,"currency_code":"GBP","in_stock":true},{"title":"1000mm and three doors","offer_id":58023123976574,"sku":"BBM-IMC-013-C100","price":1649.0,"currency_code":"GBP","in_stock":true},{"title":"1200mm and three doors","offer_id":58023124009342,"sku":"BBM-IMC-013-C120","price":1949.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Illuminated_Mirror_Cabinet_with_an_Ambient_Backlight_in_Brushed_Chrome.jpg?v=1789239737"},{"product_id":"recessed-illuminated-mirror-cabinet-in-brushed-chrome","title":"Recessed Illuminated Mirror Cabinet in Brushed Chrome","description":"\u003cp\u003eAn illuminated mirror cabinet: built into the stud wall so the door sits flush with the tiles, which needs a 105mm cavity and a decision before the plasterboard goes up.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 105mm, and the recessed version needs a 105mm cavity\u003c\/li\u003e\n\u003cli\u003eLight output: 1450 lumens from the front lighting at 82 lumens per circuit watt, which is 320 lux at the face from 400mm and is the figure that matters\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white on the front lighting as standard, which is the right temperature for a face, with a tunable option on some models\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: not dimmable as standard. A mirror light that dims is a mirror light somebody has left on 20 per cent and then complained about\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur. Not supplied with a plug, because a plug in a bathroom is not lawful\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 32.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: not fitted on this model\u003c\/li\u003e\n\u003cli\u003eCarcass: aluminium, not MDF. An MDF bathroom cabinet swells at the bottom edge within five years and there is no repairing it\u003c\/li\u003e\n\u003cli\u003eMirror: 4mm silvered float glass, safety backed to BS EN 1036\u003c\/li\u003e\n\u003cli\u003eMounting: recessed into a stud wall, template supplied\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe cabinet, assembled\u003c\/li\u003e\n\u003cli\u003ethe French cleat or the recessing frame\u003c\/li\u003e\n\u003cli\u003efixings for masonry and for stud\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe electrical connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the connection, and two people for the lift. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The cabinet hangs on a French cleat, which means you level one batten rather than four screws, and the recessed version needs its frame in before the plasterboard, so it is a decision made early or not at all.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe question that decides this purchase is where the light is. Front lit means a lit panel each side of the mirror at face height, and it is the only arrangement that lights a face evenly with no shadow under the eyes and the chin. A backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. Everything on this page is front lit, and where a model also has a backlight it is on a separate switch and described as ambient rather than as task light.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"800mm and two doors","offer_id":58023124304254,"sku":"BBM-IMC-016-C80","price":1549.0,"currency_code":"GBP","in_stock":true},{"title":"1000mm and three doors","offer_id":58023124337022,"sku":"BBM-IMC-016-C100","price":1849.0,"currency_code":"GBP","in_stock":true},{"title":"1200mm and three doors","offer_id":58023124369790,"sku":"BBM-IMC-016-C120","price":2149.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Recessed_Illuminated_Mirror_Cabinet_in_Brushed_Chrome.jpg?v=1789239869"},{"product_id":"illuminated-mirror-cabinet-with-adjustable-glass-shelves-in-brushed-chrome","title":"Illuminated Mirror Cabinet with Adjustable Glass Shelves in Brushed Chrome","description":"\u003cp\u003eAn illuminated mirror cabinet: 8mm toughened glass shelves on a 32mm pitch, so the shelf goes where the bottles are rather than where the factory put it.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 145mm, and the recessed version needs a 105mm cavity\u003c\/li\u003e\n\u003cli\u003eLight output: 1450 lumens from the front lighting at 82 lumens per circuit watt, which is 320 lux at the face from 400mm and is the figure that matters\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white on the front lighting as standard, which is the right temperature for a face, with a tunable option on some models\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: not dimmable as standard. A mirror light that dims is a mirror light somebody has left on 20 per cent and then complained about\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur. Not supplied with a plug, because a plug in a bathroom is not lawful\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 27.8 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: not fitted on this model\u003c\/li\u003e\n\u003cli\u003eCarcass: aluminium, not MDF. An MDF bathroom cabinet swells at the bottom edge within five years and there is no repairing it\u003c\/li\u003e\n\u003cli\u003eMirror: 4mm silvered float glass, safety backed to BS EN 1036\u003c\/li\u003e\n\u003cli\u003eMounting: surface mounted on a French cleat, which is a great deal easier to get level than four screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe cabinet, assembled\u003c\/li\u003e\n\u003cli\u003ethe French cleat or the recessing frame\u003c\/li\u003e\n\u003cli\u003efixings for masonry and for stud\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe electrical connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the connection, and two people for the lift. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The cabinet hangs on a French cleat, which means you level one batten rather than four screws, and the recessed version needs its frame in before the plasterboard, so it is a decision made early or not at all.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe question that decides this purchase is where the light is. Front lit means a lit panel each side of the mirror at face height, and it is the only arrangement that lights a face evenly with no shadow under the eyes and the chin. A backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. Everything on this page is front lit, and where a model also has a backlight it is on a separate switch and described as ambient rather than as task light.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"800mm and two doors","offer_id":58023124697470,"sku":"BBM-IMC-019-C80","price":1174.0,"currency_code":"GBP","in_stock":true},{"title":"1000mm and three doors","offer_id":58023124730238,"sku":"BBM-IMC-019-C100","price":1424.0,"currency_code":"GBP","in_stock":true},{"title":"1200mm and three doors","offer_id":58023124763006,"sku":"BBM-IMC-019-C120","price":1649.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Illuminated_Mirror_Cabinet_with_Adjustable_Glass_Shelves_in_Brushed_Chrome.jpg?v=1789239745"},{"product_id":"illuminated-mirror-cabinet-with-a-magnifying-mirror-in-brushed-chrome","title":"Illuminated Mirror Cabinet with a Magnifying Mirror in Brushed Chrome","description":"\u003cp\u003eAn illuminated mirror cabinet: a five times magnifying mirror on an arm inside the door, lit separately, which is what the cabinet is really for on the days it matters.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 145mm, and the recessed version needs a 105mm cavity\u003c\/li\u003e\n\u003cli\u003eLight output: 1450 lumens from the front lighting at 82 lumens per circuit watt, which is 320 lux at the face from 400mm and is the figure that matters\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white on the front lighting as standard, which is the right temperature for a face, with a tunable option on some models\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: not dimmable as standard. A mirror light that dims is a mirror light somebody has left on 20 per cent and then complained about\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur. Not supplied with a plug, because a plug in a bathroom is not lawful\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 29.2 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: not fitted on this model\u003c\/li\u003e\n\u003cli\u003eCarcass: aluminium, not MDF. An MDF bathroom cabinet swells at the bottom edge within five years and there is no repairing it\u003c\/li\u003e\n\u003cli\u003eMirror: 4mm silvered float glass, safety backed to BS EN 1036\u003c\/li\u003e\n\u003cli\u003eMounting: surface mounted on a French cleat, which is a great deal easier to get level than four screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe cabinet, assembled\u003c\/li\u003e\n\u003cli\u003ethe French cleat or the recessing frame\u003c\/li\u003e\n\u003cli\u003efixings for masonry and for stud\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe electrical connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the connection, and two people for the lift. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The cabinet hangs on a French cleat, which means you level one batten rather than four screws, and the recessed version needs its frame in before the plasterboard, so it is a decision made early or not at all.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe question that decides this purchase is where the light is. Front lit means a lit panel each side of the mirror at face height, and it is the only arrangement that lights a face evenly with no shadow under the eyes and the chin. A backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. Everything on this page is front lit, and where a model also has a backlight it is on a separate switch and described as ambient rather than as task light.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"800mm and two doors","offer_id":58023125057918,"sku":"BBM-IMC-022-C80","price":1324.0,"currency_code":"GBP","in_stock":true},{"title":"1000mm and three doors","offer_id":58023125090686,"sku":"BBM-IMC-022-C100","price":1599.0,"currency_code":"GBP","in_stock":true},{"title":"1200mm and three doors","offer_id":58023125123454,"sku":"BBM-IMC-022-C120","price":1874.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Illuminated_Mirror_Cabinet_with_a_Magnifying_Mirror_in_Brushed_Chrome.jpg?v=1789239745"},{"product_id":"illuminated-mirror-cabinet-with-a-soft-close-frame-in-brushed-chrome","title":"Illuminated Mirror Cabinet with a Soft Close Frame in Brushed Chrome","description":"\u003cp\u003eAn illuminated mirror cabinet: integrated soft close hinges rated to 80,000 cycles rather than the 20,000 that a bathroom cabinet usually gets.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 145mm, and the recessed version needs a 105mm cavity\u003c\/li\u003e\n\u003cli\u003eLight output: 1450 lumens from the front lighting at 82 lumens per circuit watt, which is 320 lux at the face from 400mm and is the figure that matters\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white on the front lighting as standard, which is the right temperature for a face, with a tunable option on some models\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: not dimmable as standard. A mirror light that dims is a mirror light somebody has left on 20 per cent and then complained about\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur. Not supplied with a plug, because a plug in a bathroom is not lawful\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 28.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: not fitted on this model\u003c\/li\u003e\n\u003cli\u003eCarcass: aluminium, not MDF. An MDF bathroom cabinet swells at the bottom edge within five years and there is no repairing it\u003c\/li\u003e\n\u003cli\u003eMirror: 4mm silvered float glass, safety backed to BS EN 1036\u003c\/li\u003e\n\u003cli\u003eMounting: surface mounted on a French cleat, which is a great deal easier to get level than four screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe cabinet, assembled\u003c\/li\u003e\n\u003cli\u003ethe French cleat or the recessing frame\u003c\/li\u003e\n\u003cli\u003efixings for masonry and for stud\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe electrical connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the connection, and two people for the lift. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The cabinet hangs on a French cleat, which means you level one batten rather than four screws, and the recessed version needs its frame in before the plasterboard, so it is a decision made early or not at all.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe question that decides this purchase is where the light is. Front lit means a lit panel each side of the mirror at face height, and it is the only arrangement that lights a face evenly with no shadow under the eyes and the chin. A backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. Everything on this page is front lit, and where a model also has a backlight it is on a separate switch and described as ambient rather than as task light.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"800mm and two doors","offer_id":58023125451134,"sku":"BBM-IMC-025-C80","price":1224.0,"currency_code":"GBP","in_stock":true},{"title":"1000mm and three doors","offer_id":58023125483902,"sku":"BBM-IMC-025-C100","price":1474.0,"currency_code":"GBP","in_stock":true},{"title":"1200mm and three doors","offer_id":58023125516670,"sku":"BBM-IMC-025-C120","price":1724.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Illuminated_Mirror_Cabinet_with_a_Soft_Close_Frame_in_Brushed_Chrome.jpg?v=1789239742"},{"product_id":"wide-illuminated-mirror-cabinet-for-two-basins-in-brushed-chrome","title":"Wide Illuminated Mirror Cabinet for Two Basins in Brushed Chrome","description":"\u003cp\u003eAn illuminated mirror cabinet: a run wide enough to sit over two basins with the front lighting split so each side switches on its own.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 145mm, and the recessed version needs a 105mm cavity\u003c\/li\u003e\n\u003cli\u003eLight output: 1450 lumens from the front lighting at 82 lumens per circuit watt, which is 320 lux at the face from 400mm and is the figure that matters\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white on the front lighting as standard, which is the right temperature for a face, with a tunable option on some models\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: not dimmable as standard. A mirror light that dims is a mirror light somebody has left on 20 per cent and then complained about\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur. Not supplied with a plug, because a plug in a bathroom is not lawful\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 38.4 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: not fitted on this model\u003c\/li\u003e\n\u003cli\u003eCarcass: aluminium, not MDF. An MDF bathroom cabinet swells at the bottom edge within five years and there is no repairing it\u003c\/li\u003e\n\u003cli\u003eMirror: 4mm silvered float glass, safety backed to BS EN 1036\u003c\/li\u003e\n\u003cli\u003eMounting: surface mounted on a French cleat, which is a great deal easier to get level than four screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe cabinet, assembled\u003c\/li\u003e\n\u003cli\u003ethe French cleat or the recessing frame\u003c\/li\u003e\n\u003cli\u003efixings for masonry and for stud\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe electrical connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the connection, and two people for the lift. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The cabinet hangs on a French cleat, which means you level one batten rather than four screws, and the recessed version needs its frame in before the plasterboard, so it is a decision made early or not at all.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe question that decides this purchase is where the light is. Front lit means a lit panel each side of the mirror at face height, and it is the only arrangement that lights a face evenly with no shadow under the eyes and the chin. A backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. Everything on this page is front lit, and where a model also has a backlight it is on a separate switch and described as ambient rather than as task light.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"800mm and two doors","offer_id":58023125877118,"sku":"BBM-IMC-028-C80","price":1749.0,"currency_code":"GBP","in_stock":true},{"title":"1000mm and three doors","offer_id":58023125909886,"sku":"BBM-IMC-028-C100","price":2099.0,"currency_code":"GBP","in_stock":true},{"title":"1200mm and three doors","offer_id":58023125942654,"sku":"BBM-IMC-028-C120","price":2449.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wide_Illuminated_Mirror_Cabinet_for_Two_Basins_in_Brushed_Chrome.jpg?v=1789239877"},{"product_id":"illuminated-mirror-cabinet-with-a-charging-shelf-in-brushed-chrome","title":"Illuminated Mirror Cabinet with a Charging Shelf in Brushed Chrome","description":"\u003cp\u003eAn illuminated mirror cabinet: a USB C and wireless charging shelf inside the cabinet on an isolated SELV supply, so the toothbrush and the razor live in the cupboard rather than on the basin.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 145mm, and the recessed version needs a 105mm cavity\u003c\/li\u003e\n\u003cli\u003eLight output: 1450 lumens from the front lighting at 82 lumens per circuit watt, which is 320 lux at the face from 400mm and is the figure that matters\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white on the front lighting as standard, which is the right temperature for a face, with a tunable option on some models\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: not dimmable as standard. A mirror light that dims is a mirror light somebody has left on 20 per cent and then complained about\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur. Not supplied with a plug, because a plug in a bathroom is not lawful\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 30.8 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: not fitted on this model\u003c\/li\u003e\n\u003cli\u003eCarcass: aluminium, not MDF. An MDF bathroom cabinet swells at the bottom edge within five years and there is no repairing it\u003c\/li\u003e\n\u003cli\u003eMirror: 4mm silvered float glass, safety backed to BS EN 1036\u003c\/li\u003e\n\u003cli\u003eMounting: surface mounted on a French cleat, which is a great deal easier to get level than four screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe cabinet, assembled\u003c\/li\u003e\n\u003cli\u003ethe French cleat or the recessing frame\u003c\/li\u003e\n\u003cli\u003efixings for masonry and for stud\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe electrical connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the connection, and two people for the lift. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The cabinet hangs on a French cleat, which means you level one batten rather than four screws, and the recessed version needs its frame in before the plasterboard, so it is a decision made early or not at all.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThe question that decides this purchase is where the light is. Front lit means a lit panel each side of the mirror at face height, and it is the only arrangement that lights a face evenly with no shadow under the eyes and the chin. A backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. Everything on this page is front lit, and where a model also has a backlight it is on a separate switch and described as ambient rather than as task light.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"800mm and two doors","offer_id":58023126335870,"sku":"BBM-IMC-031-C80","price":1424.0,"currency_code":"GBP","in_stock":true},{"title":"1000mm and three doors","offer_id":58023126368638,"sku":"BBM-IMC-031-C100","price":1724.0,"currency_code":"GBP","in_stock":true},{"title":"1200mm and three doors","offer_id":58023126401406,"sku":"BBM-IMC-031-C120","price":1999.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Illuminated_Mirror_Cabinet_with_a_Charging_Shelf_in_Brushed_Chrome.jpg?v=1789239751"},{"product_id":"front-lit-demisting-mirror-in-brushed-chrome","title":"Front Lit Demisting Mirror in Brushed Chrome","description":"\u003cp\u003eA demisting mirror, front lit: vertical lit panels each side at face height, which is the arrangement that lights a face rather than a wall.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 42mm from the wall, which is thin enough not to catch a shoulder at a basin\u003c\/li\u003e\n\u003cli\u003eLight output: 1250 lumens at 84 lumens per circuit watt, giving 300 lux at the face from 400mm, which is the figure to compare and the one nobody publishes\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white as standard\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: touch dimmable on the mirror itself, from 10 to 100 per cent, with no flicker at the bottom of the range\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur behind the mirror. A 100mm access hole is needed in the tiling and the template shows where\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 21.4 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: covers 80 per cent of the glass area, 60 watts per square metre, switched with the light and clear in about four minutes. The demister is a heated pad laminated to the back of the glass. It clears an area the size of the pad and no more, which is why the pad size is stated below rather than just the word demister. A pad that covers a third of a mirror will clear a third of a mirror.\u003c\/li\u003e\n\u003cli\u003eGlass: 5mm silvered float, safety backed to BS EN 1036, with a polished and sealed edge\u003c\/li\u003e\n\u003cli\u003eLit panels: sandblasted rather than printed, so the light is even down the whole panel instead of banded\u003c\/li\u003e\n\u003cli\u003eMounting: two brackets and a levelling screw, one person to fit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe mirror\u003c\/li\u003e\n\u003cli\u003ethe wall brackets and levelling screws\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions and a cleaning card\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the spur. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The mirror hangs on two brackets with a levelling screw, so one person can fit it and adjust it afterwards. Leave the access hole where the template shows, because reaching a connection block behind a fitted mirror through the wrong hole is a tiling job.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. That is the whole decision on this page. A front lit mirror puts 300 lux on a face from 400mm with the light coming from each side at eye height, which fills the shadows under the brow and the chin. A backlit mirror puts perhaps 40 lux on a face and all of it bounced. Buy backlit for the look and add a light above the basin, or buy front lit and be done.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"600 by 800mm","offer_id":58023126696318,"sku":"BBM-LDM-001-M68","price":1074.0,"currency_code":"GBP","in_stock":true},{"title":"800 by 800mm","offer_id":58023126729086,"sku":"BBM-LDM-001-M88","price":1324.0,"currency_code":"GBP","in_stock":true},{"title":"1000 by 800mm","offer_id":58023126761854,"sku":"BBM-LDM-001-M108","price":1549.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Front_Lit_Demisting_Mirror_in_Brushed_Chrome.jpg?v=1789239751"},{"product_id":"front-lit-demisting-mirror-with-tunable-lighting-in-brushed-chrome","title":"Front Lit Demisting Mirror with Tunable Lighting in Brushed Chrome","description":"\u003cp\u003eA demisting mirror, front lit: 2700K to 5000K on a touch control, warm for the evening and daylight for makeup.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 42mm from the wall, which is thin enough not to catch a shoulder at a basin\u003c\/li\u003e\n\u003cli\u003eLight output: 1250 lumens at 84 lumens per circuit watt, giving 300 lux at the face from 400mm, which is the figure to compare and the one nobody publishes\u003c\/li\u003e\n\u003cli\u003eColour temperature: 2700K to 5000K tunable on a touch control, and it remembers the last setting\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: touch dimmable on the mirror itself, from 10 to 100 per cent, with no flicker at the bottom of the range\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur behind the mirror. A 100mm access hole is needed in the tiling and the template shows where\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 22.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: covers 80 per cent of the glass area, 60 watts per square metre, switched with the light and clear in about four minutes. The demister is a heated pad laminated to the back of the glass. It clears an area the size of the pad and no more, which is why the pad size is stated below rather than just the word demister. A pad that covers a third of a mirror will clear a third of a mirror.\u003c\/li\u003e\n\u003cli\u003eGlass: 5mm silvered float, safety backed to BS EN 1036, with a polished and sealed edge\u003c\/li\u003e\n\u003cli\u003eLit panels: sandblasted rather than printed, so the light is even down the whole panel instead of banded\u003c\/li\u003e\n\u003cli\u003eMounting: two brackets and a levelling screw, one person to fit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe mirror\u003c\/li\u003e\n\u003cli\u003ethe wall brackets and levelling screws\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions and a cleaning card\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the spur. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The mirror hangs on two brackets with a levelling screw, so one person can fit it and adjust it afterwards. Leave the access hole where the template shows, because reaching a connection block behind a fitted mirror through the wrong hole is a tiling job.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. That is the whole decision on this page. A front lit mirror puts 300 lux on a face from 400mm with the light coming from each side at eye height, which fills the shadows under the brow and the chin. A backlit mirror puts perhaps 40 lux on a face and all of it bounced. Buy backlit for the look and add a light above the basin, or buy front lit and be done.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"600 by 800mm","offer_id":58023127089534,"sku":"BBM-LDM-004-M68","price":1274.0,"currency_code":"GBP","in_stock":true},{"title":"800 by 800mm","offer_id":58023127122302,"sku":"BBM-LDM-004-M88","price":1574.0,"currency_code":"GBP","in_stock":true},{"title":"1000 by 800mm","offer_id":58023127155070,"sku":"BBM-LDM-004-M108","price":1849.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Front_Lit_Demisting_Mirror_with_Tunable_Lighting_in_Brushed_Chrome.jpg?v=1789239743"},{"product_id":"round-front-lit-demisting-mirror-in-brushed-chrome","title":"Round Front Lit Demisting Mirror in Brushed Chrome","description":"\u003cp\u003eA demisting mirror, front lit: a round mirror with the lit panels at the three and nine o'clock positions, which is the only way a round mirror lights a face properly.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 42mm from the wall, which is thin enough not to catch a shoulder at a basin\u003c\/li\u003e\n\u003cli\u003eLight output: 1250 lumens at 84 lumens per circuit watt, giving 300 lux at the face from 400mm, which is the figure to compare and the one nobody publishes\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white as standard\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: touch dimmable on the mirror itself, from 10 to 100 per cent, with no flicker at the bottom of the range\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur behind the mirror. A 100mm access hole is needed in the tiling and the template shows where\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 19.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: covers 80 per cent of the glass area, 60 watts per square metre, switched with the light and clear in about four minutes. The demister is a heated pad laminated to the back of the glass. It clears an area the size of the pad and no more, which is why the pad size is stated below rather than just the word demister. A pad that covers a third of a mirror will clear a third of a mirror.\u003c\/li\u003e\n\u003cli\u003eGlass: 5mm silvered float, safety backed to BS EN 1036, with a polished and sealed edge\u003c\/li\u003e\n\u003cli\u003eLit panels: sandblasted rather than printed, so the light is even down the whole panel instead of banded\u003c\/li\u003e\n\u003cli\u003eMounting: two brackets and a levelling screw, one person to fit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe mirror\u003c\/li\u003e\n\u003cli\u003ethe wall brackets and levelling screws\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions and a cleaning card\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the spur. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The mirror hangs on two brackets with a levelling screw, so one person can fit it and adjust it afterwards. Leave the access hole where the template shows, because reaching a connection block behind a fitted mirror through the wrong hole is a tiling job.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. That is the whole decision on this page. A front lit mirror puts 300 lux on a face from 400mm with the light coming from each side at eye height, which fills the shadows under the brow and the chin. A backlit mirror puts perhaps 40 lux on a face and all of it bounced. Buy backlit for the look and add a light above the basin, or buy front lit and be done.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"600 by 800mm","offer_id":58023127875966,"sku":"BBM-LDM-010-M68","price":1174.0,"currency_code":"GBP","in_stock":true},{"title":"800 by 800mm","offer_id":58023127908734,"sku":"BBM-LDM-010-M88","price":1449.0,"currency_code":"GBP","in_stock":true},{"title":"1000 by 800mm","offer_id":58023127941502,"sku":"BBM-LDM-010-M108","price":1699.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Round_Front_Lit_Demisting_Mirror_in_Brushed_Chrome.jpg?v=1789239868"},{"product_id":"demisting-mirror-with-a-magnifying-insert-in-brushed-chrome","title":"Demisting Mirror with a Magnifying Insert in Brushed Chrome","description":"\u003cp\u003eA demisting mirror, front lit: a five times magnifying circle set into the main glass and lit separately.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 42mm from the wall, which is thin enough not to catch a shoulder at a basin\u003c\/li\u003e\n\u003cli\u003eLight output: 1250 lumens at 84 lumens per circuit watt, giving 300 lux at the face from 400mm, which is the figure to compare and the one nobody publishes\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white as standard\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: touch dimmable on the mirror itself, from 10 to 100 per cent, with no flicker at the bottom of the range\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur behind the mirror. A 100mm access hole is needed in the tiling and the template shows where\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 22.4 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: covers 80 per cent of the glass area, 60 watts per square metre, switched with the light and clear in about four minutes. The demister is a heated pad laminated to the back of the glass. It clears an area the size of the pad and no more, which is why the pad size is stated below rather than just the word demister. A pad that covers a third of a mirror will clear a third of a mirror.\u003c\/li\u003e\n\u003cli\u003eGlass: 5mm silvered float, safety backed to BS EN 1036, with a polished and sealed edge\u003c\/li\u003e\n\u003cli\u003eLit panels: sandblasted rather than printed, so the light is even down the whole panel instead of banded\u003c\/li\u003e\n\u003cli\u003eMounting: two brackets and a levelling screw, one person to fit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe mirror\u003c\/li\u003e\n\u003cli\u003ethe wall brackets and levelling screws\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions and a cleaning card\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the spur. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The mirror hangs on two brackets with a levelling screw, so one person can fit it and adjust it afterwards. Leave the access hole where the template shows, because reaching a connection block behind a fitted mirror through the wrong hole is a tiling job.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. That is the whole decision on this page. A front lit mirror puts 300 lux on a face from 400mm with the light coming from each side at eye height, which fills the shadows under the brow and the chin. A backlit mirror puts perhaps 40 lux on a face and all of it bounced. Buy backlit for the look and add a light above the basin, or buy front lit and be done.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"600 by 800mm","offer_id":58023128236414,"sku":"BBM-LDM-013-M68","price":1324.0,"currency_code":"GBP","in_stock":true},{"title":"800 by 800mm","offer_id":58023128269182,"sku":"BBM-LDM-013-M88","price":1624.0,"currency_code":"GBP","in_stock":true},{"title":"1000 by 800mm","offer_id":58023128301950,"sku":"BBM-LDM-013-M108","price":1924.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Demisting_Mirror_with_a_Magnifying_Insert_in_Brushed_Chrome.jpg?v=1789239660"},{"product_id":"landscape-demisting-mirror-for-two-basins-in-brushed-chrome","title":"Landscape Demisting Mirror for Two Basins in Brushed Chrome","description":"\u003cp\u003eA demisting mirror, front lit: a wide mirror with three lit panels so both basins get face light rather than one getting it and one getting a reflection of it.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 42mm from the wall, which is thin enough not to catch a shoulder at a basin\u003c\/li\u003e\n\u003cli\u003eLight output: 1250 lumens at 84 lumens per circuit watt, giving 300 lux at the face from 400mm, which is the figure to compare and the one nobody publishes\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white as standard\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: touch dimmable on the mirror itself, from 10 to 100 per cent, with no flicker at the bottom of the range\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur behind the mirror. A 100mm access hole is needed in the tiling and the template shows where\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 32.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: covers 80 per cent of the glass area, 60 watts per square metre, switched with the light and clear in about four minutes. The demister is a heated pad laminated to the back of the glass. It clears an area the size of the pad and no more, which is why the pad size is stated below rather than just the word demister. A pad that covers a third of a mirror will clear a third of a mirror.\u003c\/li\u003e\n\u003cli\u003eGlass: 5mm silvered float, safety backed to BS EN 1036, with a polished and sealed edge\u003c\/li\u003e\n\u003cli\u003eLit panels: sandblasted rather than printed, so the light is even down the whole panel instead of banded\u003c\/li\u003e\n\u003cli\u003eMounting: two brackets and a levelling screw, one person to fit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe mirror\u003c\/li\u003e\n\u003cli\u003ethe wall brackets and levelling screws\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions and a cleaning card\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the spur. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The mirror hangs on two brackets with a levelling screw, so one person can fit it and adjust it afterwards. Leave the access hole where the template shows, because reaching a connection block behind a fitted mirror through the wrong hole is a tiling job.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. That is the whole decision on this page. A front lit mirror puts 300 lux on a face from 400mm with the light coming from each side at eye height, which fills the shadows under the brow and the chin. A backlit mirror puts perhaps 40 lux on a face and all of it bounced. Buy backlit for the look and add a light above the basin, or buy front lit and be done.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"600 by 800mm","offer_id":58023128826238,"sku":"BBM-LDM-016-M68","price":1649.0,"currency_code":"GBP","in_stock":true},{"title":"800 by 800mm","offer_id":58023128859006,"sku":"BBM-LDM-016-M88","price":1999.0,"currency_code":"GBP","in_stock":true},{"title":"1000 by 800mm","offer_id":58023128891774,"sku":"BBM-LDM-016-M108","price":2374.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Landscape_Demisting_Mirror_for_Two_Basins_in_Brushed_Chrome.jpg?v=1789239872"},{"product_id":"demisting-mirror-with-a-metal-frame-in-brushed-chrome","title":"Demisting Mirror with a Metal Frame in Brushed Chrome","description":"\u003cp\u003eA demisting mirror, front lit: a 12mm metal frame around the glass, which is the detail that stops an illuminated mirror looking like a screen.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 42mm from the wall, which is thin enough not to catch a shoulder at a basin\u003c\/li\u003e\n\u003cli\u003eLight output: 1250 lumens at 84 lumens per circuit watt, giving 300 lux at the face from 400mm, which is the figure to compare and the one nobody publishes\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white as standard\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: touch dimmable on the mirror itself, from 10 to 100 per cent, with no flicker at the bottom of the range\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur behind the mirror. A 100mm access hole is needed in the tiling and the template shows where\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 26.4 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: covers 80 per cent of the glass area, 60 watts per square metre, switched with the light and clear in about four minutes. The demister is a heated pad laminated to the back of the glass. It clears an area the size of the pad and no more, which is why the pad size is stated below rather than just the word demister. A pad that covers a third of a mirror will clear a third of a mirror.\u003c\/li\u003e\n\u003cli\u003eGlass: 5mm silvered float, safety backed to BS EN 1036, with a polished and sealed edge\u003c\/li\u003e\n\u003cli\u003eLit panels: sandblasted rather than printed, so the light is even down the whole panel instead of banded\u003c\/li\u003e\n\u003cli\u003eMounting: two brackets and a levelling screw, one person to fit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe mirror\u003c\/li\u003e\n\u003cli\u003ethe wall brackets and levelling screws\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions and a cleaning card\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the spur. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The mirror hangs on two brackets with a levelling screw, so one person can fit it and adjust it afterwards. Leave the access hole where the template shows, because reaching a connection block behind a fitted mirror through the wrong hole is a tiling job.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. That is the whole decision on this page. A front lit mirror puts 300 lux on a face from 400mm with the light coming from each side at eye height, which fills the shadows under the brow and the chin. A backlit mirror puts perhaps 40 lux on a face and all of it bounced. Buy backlit for the look and add a light above the basin, or buy front lit and be done.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"600 by 800mm","offer_id":58023129645438,"sku":"BBM-LDM-022-M68","price":1499.0,"currency_code":"GBP","in_stock":true},{"title":"800 by 800mm","offer_id":58023129678206,"sku":"BBM-LDM-022-M88","price":1824.0,"currency_code":"GBP","in_stock":true},{"title":"1000 by 800mm","offer_id":58023129710974,"sku":"BBM-LDM-022-M108","price":2149.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Demisting_Mirror_with_a_Metal_Frame_in_Brushed_Chrome.jpg?v=1789239659"},{"product_id":"full-height-demisting-mirror-in-brushed-chrome","title":"Full Height Demisting Mirror in Brushed Chrome","description":"\u003cp\u003eA demisting mirror, front lit: a 1600mm mirror lit down both edges, for a bathroom where the mirror is the wall.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: chosen above. Depth 42mm from the wall, which is thin enough not to catch a shoulder at a basin\u003c\/li\u003e\n\u003cli\u003eLight output: 1250 lumens at 84 lumens per circuit watt, giving 300 lux at the face from 400mm, which is the figure to compare and the one nobody publishes\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K neutral white as standard\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: touch dimmable on the mirror itself, from 10 to 100 per cent, with no flicker at the bottom of the range\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, hard wired to a fused spur behind the mirror. A 100mm access hole is needed in the tiling and the template shows where\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598-2-1, BS EN 1036 for the silvered glass, and BS EN 12150 for the toughened substrate. Every mirror is safety backed so it holds together if it is broken\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 34.8 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eDemister pad: covers 80 per cent of the glass area, 60 watts per square metre, switched with the light and clear in about four minutes. The demister is a heated pad laminated to the back of the glass. It clears an area the size of the pad and no more, which is why the pad size is stated below rather than just the word demister. A pad that covers a third of a mirror will clear a third of a mirror.\u003c\/li\u003e\n\u003cli\u003eGlass: 5mm silvered float, safety backed to BS EN 1036, with a polished and sealed edge\u003c\/li\u003e\n\u003cli\u003eLit panels: sandblasted rather than printed, so the light is even down the whole panel instead of banded\u003c\/li\u003e\n\u003cli\u003eMounting: two brackets and a levelling screw, one person to fit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe mirror\u003c\/li\u003e\n\u003cli\u003ethe wall brackets and levelling screws\u003c\/li\u003e\n\u003cli\u003ea paper drilling template\u003c\/li\u003e\n\u003cli\u003ethe connection block and gland\u003c\/li\u003e\n\u003cli\u003einstallation instructions and a cleaning card\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician for the spur. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The mirror hangs on two brackets with a levelling screw, so one person can fit it and adjust it afterwards. Leave the access hole where the template shows, because reaching a connection block behind a fitted mirror through the wrong hole is a tiling job.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA backlit mirror throws its light at the wall behind it and returns a halo. It is beautiful and it does not light your face. If this mirror is the only light source at your basin, choose a front lit one instead, or add a light above. That is the whole decision on this page. A front lit mirror puts 300 lux on a face from 400mm with the light coming from each side at eye height, which fills the shadows under the brow and the chin. A backlit mirror puts perhaps 40 lux on a face and all of it bounced. Buy backlit for the look and add a light above the basin, or buy front lit and be done.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"600 by 800mm","offer_id":58023130464638,"sku":"BBM-LDM-028-M68","price":1749.0,"currency_code":"GBP","in_stock":true},{"title":"800 by 800mm","offer_id":58023130497406,"sku":"BBM-LDM-028-M88","price":2124.0,"currency_code":"GBP","in_stock":true},{"title":"1000 by 800mm","offer_id":58023130530174,"sku":"BBM-LDM-028-M108","price":2524.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Full_Height_Demisting_Mirror_in_Brushed_Chrome.jpg?v=1789239740"},{"product_id":"hotel-bathroom-lighting-package-for-ten-rooms-in-brushed-chrome","title":"Hotel Bathroom Lighting Package for Ten Rooms in Brushed Chrome","description":"\u003cp\u003eA contract package: ten identical en suite packages with matched batch LEDs, so room 12 and room 34 are the same colour, which guests do not consciously notice and photographers do.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: per the schedule supplied with the quotation\u003c\/li\u003e\n\u003cli\u003eLight output: sized to 200 lux general and 500 lux at the mirror, which is the CIBSE recommendation for a washroom and the number a specifier will check\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K throughout as standard, batch matched across the whole order\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: DALI 2 addressable, so the scheme can be commissioned and recommissioned without rewiring\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, DALI drivers, with 20 per cent spare capacity designed into every circuit\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus BS 5266 for the emergency luminaires where fitted\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 84.6 kilograms for the package\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years parts and labour on site, extendable to seven\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eBatch matching: every LED module in one order comes from one bin, within a 3 step MacAdam ellipse, so the rooms match each other\u003c\/li\u003e\n\u003cli\u003eEmergency: not included, and available as an addition\u003c\/li\u003e\n\u003cli\u003eDocuments: photometric calculations, a lighting schedule, DALI addressing sheet, emergency test log and O and M manual\u003c\/li\u003e\n\u003cli\u003eSpares: every part held in UK stock for ten years\u003c\/li\u003e\n\u003cli\u003eAccount: 30 day terms on approval, and we take purchase orders\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery luminaire in the package\u003c\/li\u003e\n\u003cli\u003eDALI drivers and the addressing sheet\u003c\/li\u003e\n\u003cli\u003eemergency luminaires where specified\u003c\/li\u003e\n\u003cli\u003ea photometric calculation for the room\u003c\/li\u003e\n\u003cli\u003ethe lighting schedule and O and M manual\u003c\/li\u003e\n\u003cli\u003ea spares kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eInstallation is quoted per site and is usually the right answer, because DALI addressing and emergency commissioning both have to be recorded. Our electricians carry public liability cover, work to your site hours, and issue the test certificates and the O and M manual on completion rather than three weeks later.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThree questions separate a contract supplier from a box shifter. Can you batch match the LEDs so twenty rooms are the same colour. Can you produce a photometric calculation rather than a guess at how many downlights. Will the parts still exist in year six. The answers here are yes, yes and yes, and every one of them is checkable before you place the order.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Supplied only","offer_id":58023131185534,"sku":"BBM-COM-002-SO","price":2474.0,"currency_code":"GBP","in_stock":true},{"title":"Supplied and installed by our electricians","offer_id":58023131218302,"sku":"BBM-COM-002-SI","price":3149.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Hotel_Bathroom_Lighting_Package_for_Ten_Rooms_in_Brushed_Chrome.jpg?v=1789239744"},{"product_id":"commercial-washroom-lighting-package-in-brushed-chrome","title":"Commercial Washroom Lighting Package in Brushed Chrome","description":"\u003cp\u003eA contract package: IP65 throughout, vandal resistant lenses and a DALI backbone, for a washroom that gets a hundred people a day.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: per the schedule supplied with the quotation\u003c\/li\u003e\n\u003cli\u003eLight output: sized to 200 lux general and 500 lux at the mirror, which is the CIBSE recommendation for a washroom and the number a specifier will check\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K throughout as standard, batch matched across the whole order\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: DALI 2 addressable, so the scheme can be commissioned and recommissioned without rewiring\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, DALI drivers, with 20 per cent spare capacity designed into every circuit\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus BS 5266 for the emergency luminaires where fitted\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 78.2 kilograms for the package\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years parts and labour on site, extendable to seven\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eBatch matching: every LED module in one order comes from one bin, within a 3 step MacAdam ellipse, so the rooms match each other\u003c\/li\u003e\n\u003cli\u003eEmergency: not included, and available as an addition\u003c\/li\u003e\n\u003cli\u003eDocuments: photometric calculations, a lighting schedule, DALI addressing sheet, emergency test log and O and M manual\u003c\/li\u003e\n\u003cli\u003eSpares: every part held in UK stock for ten years\u003c\/li\u003e\n\u003cli\u003eAccount: 30 day terms on approval, and we take purchase orders\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery luminaire in the package\u003c\/li\u003e\n\u003cli\u003eDALI drivers and the addressing sheet\u003c\/li\u003e\n\u003cli\u003eemergency luminaires where specified\u003c\/li\u003e\n\u003cli\u003ea photometric calculation for the room\u003c\/li\u003e\n\u003cli\u003ethe lighting schedule and O and M manual\u003c\/li\u003e\n\u003cli\u003ea spares kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eInstallation is quoted per site and is usually the right answer, because DALI addressing and emergency commissioning both have to be recorded. Our electricians carry public liability cover, work to your site hours, and issue the test certificates and the O and M manual on completion rather than three weeks later.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThree questions separate a contract supplier from a box shifter. Can you batch match the LEDs so twenty rooms are the same colour. Can you produce a photometric calculation rather than a guess at how many downlights. Will the parts still exist in year six. The answers here are yes, yes and yes, and every one of them is checkable before you place the order.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Supplied only","offer_id":58023131775358,"sku":"BBM-COM-008-SO","price":2249.0,"currency_code":"GBP","in_stock":true},{"title":"Supplied and installed by our electricians","offer_id":58023131808126,"sku":"BBM-COM-008-SI","price":2899.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Commercial_Washroom_Lighting_Package_in_Brushed_Chrome.jpg?v=1789239649"},{"product_id":"care-home-bathroom-lighting-package-in-brushed-chrome","title":"Care Home Bathroom Lighting Package in Brushed Chrome","description":"\u003cp\u003eA contract package: high CRI at 500 lux for staff carrying out personal care, a night circuit at 5 lux, and no glare from a lying position, which is the specification most care home bathrooms miss.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: per the schedule supplied with the quotation\u003c\/li\u003e\n\u003cli\u003eLight output: sized to 200 lux general and 500 lux at the mirror, which is the CIBSE recommendation for a washroom and the number a specifier will check\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K throughout as standard, batch matched across the whole order\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: DALI 2 addressable, so the scheme can be commissioned and recommissioned without rewiring\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, DALI drivers, with 20 per cent spare capacity designed into every circuit\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus BS 5266 for the emergency luminaires where fitted\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 82.8 kilograms for the package\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years parts and labour on site, extendable to seven\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eBatch matching: every LED module in one order comes from one bin, within a 3 step MacAdam ellipse, so the rooms match each other\u003c\/li\u003e\n\u003cli\u003eEmergency: not included, and available as an addition\u003c\/li\u003e\n\u003cli\u003eDocuments: photometric calculations, a lighting schedule, DALI addressing sheet, emergency test log and O and M manual\u003c\/li\u003e\n\u003cli\u003eSpares: every part held in UK stock for ten years\u003c\/li\u003e\n\u003cli\u003eAccount: 30 day terms on approval, and we take purchase orders\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery luminaire in the package\u003c\/li\u003e\n\u003cli\u003eDALI drivers and the addressing sheet\u003c\/li\u003e\n\u003cli\u003eemergency luminaires where specified\u003c\/li\u003e\n\u003cli\u003ea photometric calculation for the room\u003c\/li\u003e\n\u003cli\u003ethe lighting schedule and O and M manual\u003c\/li\u003e\n\u003cli\u003ea spares kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eInstallation is quoted per site and is usually the right answer, because DALI addressing and emergency commissioning both have to be recorded. Our electricians carry public liability cover, work to your site hours, and issue the test certificates and the O and M manual on completion rather than three weeks later.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThree questions separate a contract supplier from a box shifter. Can you batch match the LEDs so twenty rooms are the same colour. Can you produce a photometric calculation rather than a guess at how many downlights. Will the parts still exist in year six. The answers here are yes, yes and yes, and every one of them is checkable before you place the order.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Supplied only","offer_id":58023132070270,"sku":"BBM-COM-011-SO","price":2574.0,"currency_code":"GBP","in_stock":true},{"title":"Supplied and installed by our electricians","offer_id":58023132103038,"sku":"BBM-COM-011-SI","price":3299.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Care_Home_Bathroom_Lighting_Package_in_Brushed_Chrome.jpg?v=1789239641"},{"product_id":"gym-and-changing-room-lighting-package-in-brushed-chrome","title":"Gym and Changing Room Lighting Package in Brushed Chrome","description":"\u003cp\u003eA contract package: IP65, impact rated to IK08, and an occupancy sensed circuit that leaves 10 per cent on so nobody walks into a dark changing room.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: per the schedule supplied with the quotation\u003c\/li\u003e\n\u003cli\u003eLight output: sized to 200 lux general and 500 lux at the mirror, which is the CIBSE recommendation for a washroom and the number a specifier will check\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K throughout as standard, batch matched across the whole order\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: DALI 2 addressable, so the scheme can be commissioned and recommissioned without rewiring\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, DALI drivers, with 20 per cent spare capacity designed into every circuit\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus BS 5266 for the emergency luminaires where fitted\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 96.4 kilograms for the package\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years parts and labour on site, extendable to seven\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eBatch matching: every LED module in one order comes from one bin, within a 3 step MacAdam ellipse, so the rooms match each other\u003c\/li\u003e\n\u003cli\u003eEmergency: not included, and available as an addition\u003c\/li\u003e\n\u003cli\u003eDocuments: photometric calculations, a lighting schedule, DALI addressing sheet, emergency test log and O and M manual\u003c\/li\u003e\n\u003cli\u003eSpares: every part held in UK stock for ten years\u003c\/li\u003e\n\u003cli\u003eAccount: 30 day terms on approval, and we take purchase orders\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery luminaire in the package\u003c\/li\u003e\n\u003cli\u003eDALI drivers and the addressing sheet\u003c\/li\u003e\n\u003cli\u003eemergency luminaires where specified\u003c\/li\u003e\n\u003cli\u003ea photometric calculation for the room\u003c\/li\u003e\n\u003cli\u003ethe lighting schedule and O and M manual\u003c\/li\u003e\n\u003cli\u003ea spares kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eInstallation is quoted per site and is usually the right answer, because DALI addressing and emergency commissioning both have to be recorded. Our electricians carry public liability cover, work to your site hours, and issue the test certificates and the O and M manual on completion rather than three weeks later.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThree questions separate a contract supplier from a box shifter. Can you batch match the LEDs so twenty rooms are the same colour. Can you produce a photometric calculation rather than a guess at how many downlights. Will the parts still exist in year six. The answers here are yes, yes and yes, and every one of them is checkable before you place the order.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Supplied only","offer_id":58023132332414,"sku":"BBM-COM-014-SO","price":2424.0,"currency_code":"GBP","in_stock":true},{"title":"Supplied and installed by our electricians","offer_id":58023132365182,"sku":"BBM-COM-014-SI","price":3099.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Gym_and_Changing_Room_Lighting_Package_in_Brushed_Chrome.jpg?v=1789239747"},{"product_id":"student-accommodation-washroom-package-in-brushed-chrome","title":"Student Accommodation Washroom Package in Brushed Chrome","description":"\u003cp\u003eA contract package: vandal resistant IP65 fittings with captive screws, on a maintained emergency circuit, and every part still available in five years.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: per the schedule supplied with the quotation\u003c\/li\u003e\n\u003cli\u003eLight output: sized to 200 lux general and 500 lux at the mirror, which is the CIBSE recommendation for a washroom and the number a specifier will check\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K throughout as standard, batch matched across the whole order\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: DALI 2 addressable, so the scheme can be commissioned and recommissioned without rewiring\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, DALI drivers, with 20 per cent spare capacity designed into every circuit\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus BS 5266 for the emergency luminaires where fitted\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 88.6 kilograms for the package\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years parts and labour on site, extendable to seven\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eBatch matching: every LED module in one order comes from one bin, within a 3 step MacAdam ellipse, so the rooms match each other\u003c\/li\u003e\n\u003cli\u003eEmergency: three hour maintained to BS 5266 with a monthly and annual test schedule supplied\u003c\/li\u003e\n\u003cli\u003eDocuments: photometric calculations, a lighting schedule, DALI addressing sheet, emergency test log and O and M manual\u003c\/li\u003e\n\u003cli\u003eSpares: every part held in UK stock for ten years\u003c\/li\u003e\n\u003cli\u003eAccount: 30 day terms on approval, and we take purchase orders\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery luminaire in the package\u003c\/li\u003e\n\u003cli\u003eDALI drivers and the addressing sheet\u003c\/li\u003e\n\u003cli\u003eemergency luminaires where specified\u003c\/li\u003e\n\u003cli\u003ea photometric calculation for the room\u003c\/li\u003e\n\u003cli\u003ethe lighting schedule and O and M manual\u003c\/li\u003e\n\u003cli\u003ea spares kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eInstallation is quoted per site and is usually the right answer, because DALI addressing and emergency commissioning both have to be recorded. Our electricians carry public liability cover, work to your site hours, and issue the test certificates and the O and M manual on completion rather than three weeks later.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThree questions separate a contract supplier from a box shifter. Can you batch match the LEDs so twenty rooms are the same colour. Can you produce a photometric calculation rather than a guess at how many downlights. Will the parts still exist in year six. The answers here are yes, yes and yes, and every one of them is checkable before you place the order.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Supplied only","offer_id":58023132823934,"sku":"BBM-COM-020-SO","price":2199.0,"currency_code":"GBP","in_stock":true},{"title":"Supplied and installed by our electricians","offer_id":58023132856702,"sku":"BBM-COM-020-SI","price":2824.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Student_Accommodation_Washroom_Package_in_Brushed_Chrome.jpg?v=1789239877"},{"product_id":"restaurant-washroom-lighting-package-in-brushed-chrome","title":"Restaurant Washroom Lighting Package in Brushed Chrome","description":"\u003cp\u003eA contract package: a scheme where the washroom is part of the design rather than an afterthought, with warm high CRI light and a flattering mirror position.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: per the schedule supplied with the quotation\u003c\/li\u003e\n\u003cli\u003eLight output: sized to 200 lux general and 500 lux at the mirror, which is the CIBSE recommendation for a washroom and the number a specifier will check\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K throughout as standard, batch matched across the whole order\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: DALI 2 addressable, so the scheme can be commissioned and recommissioned without rewiring\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, DALI drivers, with 20 per cent spare capacity designed into every circuit\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus BS 5266 for the emergency luminaires where fitted\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 74.2 kilograms for the package\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years parts and labour on site, extendable to seven\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eBatch matching: every LED module in one order comes from one bin, within a 3 step MacAdam ellipse, so the rooms match each other\u003c\/li\u003e\n\u003cli\u003eEmergency: not included, and available as an addition\u003c\/li\u003e\n\u003cli\u003eDocuments: photometric calculations, a lighting schedule, DALI addressing sheet, emergency test log and O and M manual\u003c\/li\u003e\n\u003cli\u003eSpares: every part held in UK stock for ten years\u003c\/li\u003e\n\u003cli\u003eAccount: 30 day terms on approval, and we take purchase orders\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery luminaire in the package\u003c\/li\u003e\n\u003cli\u003eDALI drivers and the addressing sheet\u003c\/li\u003e\n\u003cli\u003eemergency luminaires where specified\u003c\/li\u003e\n\u003cli\u003ea photometric calculation for the room\u003c\/li\u003e\n\u003cli\u003ethe lighting schedule and O and M manual\u003c\/li\u003e\n\u003cli\u003ea spares kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eInstallation is quoted per site and is usually the right answer, because DALI addressing and emergency commissioning both have to be recorded. Our electricians carry public liability cover, work to your site hours, and issue the test certificates and the O and M manual on completion rather than three weeks later.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThree questions separate a contract supplier from a box shifter. Can you batch match the LEDs so twenty rooms are the same colour. Can you produce a photometric calculation rather than a guess at how many downlights. Will the parts still exist in year six. The answers here are yes, yes and yes, and every one of them is checkable before you place the order.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Supplied only","offer_id":58023133053310,"sku":"BBM-COM-023-SO","price":2674.0,"currency_code":"GBP","in_stock":true},{"title":"Supplied and installed by our electricians","offer_id":58023133086078,"sku":"BBM-COM-023-SI","price":3424.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Restaurant_Washroom_Lighting_Package_in_Brushed_Chrome.jpg?v=1789239874"},{"product_id":"office-washroom-lighting-package-with-presence-detection-in-brushed-chrome","title":"Office Washroom Lighting Package with Presence Detection in Brushed Chrome","description":"\u003cp\u003eA contract package: presence detection with a five minute hold and a daylight override, which is the easiest energy saving in any commercial building and the one most often specified badly.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2 and outside the zones, which is every position in a domestic bathroom except inside the bath itself\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: per the schedule supplied with the quotation\u003c\/li\u003e\n\u003cli\u003eLight output: sized to 200 lux general and 500 lux at the mirror, which is the CIBSE recommendation for a washroom and the number a specifier will check\u003c\/li\u003e\n\u003cli\u003eColour temperature: 4000K throughout as standard, batch matched across the whole order\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: DALI 2 addressable, so the scheme can be commissioned and recommissioned without rewiring\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, DALI drivers, with 20 per cent spare capacity designed into every circuit\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus BS 5266 for the emergency luminaires where fitted\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 76.8 kilograms for the package\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years parts and labour on site, extendable to seven\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eBatch matching: every LED module in one order comes from one bin, within a 3 step MacAdam ellipse, so the rooms match each other\u003c\/li\u003e\n\u003cli\u003eEmergency: not included, and available as an addition\u003c\/li\u003e\n\u003cli\u003eDocuments: photometric calculations, a lighting schedule, DALI addressing sheet, emergency test log and O and M manual\u003c\/li\u003e\n\u003cli\u003eSpares: every part held in UK stock for ten years\u003c\/li\u003e\n\u003cli\u003eAccount: 30 day terms on approval, and we take purchase orders\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery luminaire in the package\u003c\/li\u003e\n\u003cli\u003eDALI drivers and the addressing sheet\u003c\/li\u003e\n\u003cli\u003eemergency luminaires where specified\u003c\/li\u003e\n\u003cli\u003ea photometric calculation for the room\u003c\/li\u003e\n\u003cli\u003ethe lighting schedule and O and M manual\u003c\/li\u003e\n\u003cli\u003ea spares kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eInstallation is quoted per site and is usually the right answer, because DALI addressing and emergency commissioning both have to be recorded. Our electricians carry public liability cover, work to your site hours, and issue the test certificates and the O and M manual on completion rather than three weeks later.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eThree questions separate a contract supplier from a box shifter. Can you batch match the LEDs so twenty rooms are the same colour. Can you produce a photometric calculation rather than a guess at how many downlights. Will the parts still exist in year six. The answers here are yes, yes and yes, and every one of them is checkable before you place the order.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Supplied only","offer_id":58023133446526,"sku":"BBM-COM-029-SO","price":2374.0,"currency_code":"GBP","in_stock":true},{"title":"Supplied and installed by our electricians","offer_id":58023133479294,"sku":"BBM-COM-029-SI","price":3024.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Office_Washroom_Lighting_Package_with_Presence_Detection_in_Brushed_Chrome.jpg?v=1789239869"},{"product_id":"fire-rated-ip65-downlight-trade-pack-with-cri-97-in-brushed-chrome","title":"Fire Rated IP65 Downlight Trade Pack with CRI 97 in Brushed Chrome","description":"\u003cp\u003eA trade pack of fire rated downlights: CRI 97 with R9 above 90, which is a photographic specification and worth the money in a bathroom and a kitchen and nowhere else.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: 85mm cut out, 92mm overall diameter, 55mm insertion depth above the ceiling\u003c\/li\u003e\n\u003cli\u003eLight output: 650 lumens per fitting at 92 lumens per circuit watt. Efficacy is quoted in lumens per circuit watt, which counts the driver losses, rather than lumens per chip watt, which does not. Part L of the Building Regulations asks for 75 lumens per circuit watt on new work and a great many fittings sold as compliant are quoted the other way.\u003c\/li\u003e\n\u003cli\u003eColour temperature: 3000K as standard, or selectable on the models that say so\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, trailing edge, to 1 per cent without flicker or drop out\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus BS 476 Part 21 fire testing with certificates for both plasterboard and timber joist constructions\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.5 kilograms per fitting\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003ePack: chosen above, and the price per fitting falls at twenty and again at thirty\u003c\/li\u003e\n\u003cli\u003eInsulation: may be covered directly with insulation, no hood required, which is the whole point of an integrated fire rated fitting\u003c\/li\u003e\n\u003cli\u003eInsertion depth: 55mm, which clears a 47mm joist void and is the number that catches people out on a first floor bathroom\u003c\/li\u003e\n\u003cli\u003eCertificates: fire, IP and photometric test reports downloadable from this page rather than on request\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe fittings, with integral drivers and flex tails\u003c\/li\u003e\n\u003cli\u003eIP65 rated push fit connectors\u003c\/li\u003e\n\u003cli\u003espare gaskets\u003c\/li\u003e\n\u003cli\u003ea cut out template\u003c\/li\u003e\n\u003cli\u003efire and IP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The fitting is fire rated in itself, so no hood is needed and insulation may be laid straight over it. Check the 55mm insertion depth against your joist void before you cut the first hole, because a first floor bathroom ceiling with 47mm joists and a plasterboard skin is tighter than it looks.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eFire rating is not a nice to have. If the ceiling below the bathroom is a fire compartment, which it is in every flat and in most two storey houses where the room below is habitable, cutting an 85mm hole in it without a fire rated fitting or a hood breaches Part B of the Building Regulations. The certificate for these is on this page, for both plasterboard and timber joist constructions, because a fitting tested in only one of those is only rated in one of those.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Pack of ten","offer_id":58023134462334,"sku":"BBM-FRP-010-P10","price":1274.0,"currency_code":"GBP","in_stock":true},{"title":"Pack of twenty","offer_id":58023134495102,"sku":"BBM-FRP-010-P20","price":2449.0,"currency_code":"GBP","in_stock":true},{"title":"Pack of thirty","offer_id":58023134527870,"sku":"BBM-FRP-010-P30","price":3549.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Fire_Rated_IP65_Downlight_Trade_Pack_with_CRI_97_in_Brushed_Chrome.jpg?v=1789239740"},{"product_id":"fire-rated-airtight-ip65-downlight-trade-pack-in-brushed-chrome","title":"Fire Rated Airtight IP65 Downlight Trade Pack in Brushed Chrome","description":"\u003cp\u003eA trade pack of fire rated downlights: airtight to less than 0.5 cubic metres an hour, which is what a passive house or an airtightness test needs and what a normal downlight destroys.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: 85mm cut out, 92mm overall diameter, 55mm insertion depth above the ceiling\u003c\/li\u003e\n\u003cli\u003eLight output: 650 lumens per fitting at 92 lumens per circuit watt. Efficacy is quoted in lumens per circuit watt, which counts the driver losses, rather than lumens per chip watt, which does not. Part L of the Building Regulations asks for 75 lumens per circuit watt on new work and a great many fittings sold as compliant are quoted the other way.\u003c\/li\u003e\n\u003cli\u003eColour temperature: 3000K as standard, or selectable on the models that say so\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, trailing edge, to 1 per cent without flicker or drop out\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus BS 476 Part 21 fire testing with certificates for both plasterboard and timber joist constructions\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.5 kilograms per fitting\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003ePack: chosen above, and the price per fitting falls at twenty and again at thirty\u003c\/li\u003e\n\u003cli\u003eInsulation: may be covered directly with insulation, no hood required, which is the whole point of an integrated fire rated fitting\u003c\/li\u003e\n\u003cli\u003eInsertion depth: 55mm, which clears a 47mm joist void and is the number that catches people out on a first floor bathroom\u003c\/li\u003e\n\u003cli\u003eCertificates: fire, IP and photometric test reports downloadable from this page rather than on request\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe fittings, with integral drivers and flex tails\u003c\/li\u003e\n\u003cli\u003eIP65 rated push fit connectors\u003c\/li\u003e\n\u003cli\u003espare gaskets\u003c\/li\u003e\n\u003cli\u003ea cut out template\u003c\/li\u003e\n\u003cli\u003efire and IP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The fitting is fire rated in itself, so no hood is needed and insulation may be laid straight over it. Check the 55mm insertion depth against your joist void before you cut the first hole, because a first floor bathroom ceiling with 47mm joists and a plasterboard skin is tighter than it looks.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eFire rating is not a nice to have. If the ceiling below the bathroom is a fire compartment, which it is in every flat and in most two storey houses where the room below is habitable, cutting an 85mm hole in it without a fire rated fitting or a hood breaches Part B of the Building Regulations. The certificate for these is on this page, for both plasterboard and timber joist constructions, because a fitting tested in only one of those is only rated in one of those.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Pack of ten","offer_id":58023134757246,"sku":"BBM-FRP-013-P10","price":1224.0,"currency_code":"GBP","in_stock":true},{"title":"Pack of twenty","offer_id":58023134790014,"sku":"BBM-FRP-013-P20","price":2374.0,"currency_code":"GBP","in_stock":true},{"title":"Pack of thirty","offer_id":58023134822782,"sku":"BBM-FRP-013-P30","price":3399.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Fire_Rated_Airtight_IP65_Downlight_Trade_Pack_in_Brushed_Chrome.jpg?v=1789239740"},{"product_id":"fire-rated-acoustic-ip65-downlight-trade-pack-in-brushed-chrome","title":"Fire Rated Acoustic IP65 Downlight Trade Pack in Brushed Chrome","description":"\u003cp\u003eA trade pack of fire rated downlights: an acoustic hood integrated into the fitting, keeping a 45dB floor at 45dB, which matters in a flat and is a building control question.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: 85mm cut out, 92mm overall diameter, 55mm insertion depth above the ceiling\u003c\/li\u003e\n\u003cli\u003eLight output: 650 lumens per fitting at 92 lumens per circuit watt. Efficacy is quoted in lumens per circuit watt, which counts the driver losses, rather than lumens per chip watt, which does not. Part L of the Building Regulations asks for 75 lumens per circuit watt on new work and a great many fittings sold as compliant are quoted the other way.\u003c\/li\u003e\n\u003cli\u003eColour temperature: 3000K as standard, or selectable on the models that say so\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, trailing edge, to 1 per cent without flicker or drop out\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus BS 476 Part 21 fire testing with certificates for both plasterboard and timber joist constructions\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 0.6 kilograms per fitting\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003ePack: chosen above, and the price per fitting falls at twenty and again at thirty\u003c\/li\u003e\n\u003cli\u003eInsulation: may be covered directly with insulation, no hood required, which is the whole point of an integrated fire rated fitting\u003c\/li\u003e\n\u003cli\u003eInsertion depth: 55mm, which clears a 47mm joist void and is the number that catches people out on a first floor bathroom\u003c\/li\u003e\n\u003cli\u003eCertificates: fire, IP and photometric test reports downloadable from this page rather than on request\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe fittings, with integral drivers and flex tails\u003c\/li\u003e\n\u003cli\u003eIP65 rated push fit connectors\u003c\/li\u003e\n\u003cli\u003espare gaskets\u003c\/li\u003e\n\u003cli\u003ea cut out template\u003c\/li\u003e\n\u003cli\u003efire and IP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The fitting is fire rated in itself, so no hood is needed and insulation may be laid straight over it. Check the 55mm insertion depth against your joist void before you cut the first hole, because a first floor bathroom ceiling with 47mm joists and a plasterboard skin is tighter than it looks.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eFire rating is not a nice to have. If the ceiling below the bathroom is a fire compartment, which it is in every flat and in most two storey houses where the room below is habitable, cutting an 85mm hole in it without a fire rated fitting or a hood breaches Part B of the Building Regulations. The certificate for these is on this page, for both plasterboard and timber joist constructions, because a fitting tested in only one of those is only rated in one of those.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"Pack of ten","offer_id":58023135052158,"sku":"BBM-FRP-016-P10","price":1374.0,"currency_code":"GBP","in_stock":true},{"title":"Pack of twenty","offer_id":58023135084926,"sku":"BBM-FRP-016-P20","price":2649.0,"currency_code":"GBP","in_stock":true},{"title":"Pack of thirty","offer_id":58023135117694,"sku":"BBM-FRP-016-P30","price":3824.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Fire_Rated_Acoustic_IP65_Downlight_Trade_Pack_in_Brushed_Chrome.jpg?v=1789239740"}],"url":"https:\/\/batheandbeam.com\/collections\/brushed-chrome.oembed?page=3","provider":"Bathe \u0026 Beam","version":"1.0","type":"link"}