{"title":"Marine Grade 316 Stainless","description":"\u003cp\u003e316 stainless resists chloride corrosion in a way that 304 does not. Specify it for coastal houses, swimming pools, steam rooms and leisure wet areas, where ordinary chrome plating blisters within a couple of years.\u003c\/p\u003e","products":[{"product_id":"marine-grade-wet-room-lighting-package-in-brushed-stainless","title":"Marine Grade Wet Room Lighting Package in Brushed Stainless","description":"\u003cp\u003eFor a room that is wet all day: 316 stainless throughout, because a wet room is wet all day and 304 stainless will tea stain in a couple of years.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 13.2 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eCorrosion: 316 marine grade stainless, salt spray tested to 1000 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023118799230,"sku":"BBM-WRP-002-27","price":2474.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023118831998,"sku":"BBM-WRP-002-30","price":2474.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023118864766,"sku":"BBM-WRP-002-40","price":2474.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Marine_Grade_Wet_Room_Lighting_Package_in_Brushed_Stainless.jpg?v=1789239864"},{"product_id":"wet-room-lighting-package-with-zone-0-floor-lights-in-brushed-stainless","title":"Wet Room Lighting Package with Zone 0 Floor Lights in Brushed Stainless","description":"\u003cp\u003eFor a room that is wet all day: IP67 SELV floor lights inside the shower area itself, running at 12 volts with the transformer outside the zones, which is the only lawful way to put a light there.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 0, which is inside the bath or the shower tray itself. A fitting here must be IP67 and must run at SELV, meaning 12 volts or less with the transformer outside the zones\u003c\/li\u003e\n\u003cli\u003eIP rating: IP67. Dust tight and protected against temporary immersion in up to a metre of water, which is what zone 0 requires and what a fitting in a shower tray or a bath surround has to be\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: SELV, 12 volts, with the transformer sited outside the zones. This is what makes the fitting legal in zone 0 and it is not optional\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 14.9 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eCorrosion: 316 marine grade stainless, salt spray tested to 1000 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023119192446,"sku":"BBM-WRP-005-27","price":2924.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023119225214,"sku":"BBM-WRP-005-30","price":2924.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023119257982,"sku":"BBM-WRP-005-40","price":2924.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wet_Room_Lighting_Package_with_Zone_0_Floor_Lights_in_Brushed_Stainless.jpg?v=1789239878"},{"product_id":"steam-room-lighting-package-in-brushed-stainless","title":"Steam Room Lighting Package in Brushed Stainless","description":"\u003cp\u003eFor a room that is wet all day: fittings rated to 60 degrees ambient with silicone gaskets rather than nitrile, because a nitrile gasket in a steam room hardens and lets water in within a season.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 17.5 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eCorrosion: 316 marine grade stainless, salt spray tested to 1000 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 60 degrees, which is a steam room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023119552894,"sku":"BBM-WRP-008-27","price":3549.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023119585662,"sku":"BBM-WRP-008-30","price":3549.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023119618430,"sku":"BBM-WRP-008-40","price":3549.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Steam_Room_Lighting_Package_in_Brushed_Stainless.jpg?v=1789239876"},{"product_id":"wet-room-lighting-package-with-a-recessed-shower-light-in-brushed-stainless","title":"Wet Room Lighting Package with a Recessed Shower Light in Brushed Stainless","description":"\u003cp\u003eFor a room that is wet all day: a flush IP65 light directly over the shower with a tempered glass lens and a captive gasket, so it can be cleaned without dropping the lens.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 12.3 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eCorrosion: 316 marine grade stainless, salt spray tested to 1000 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023119946110,"sku":"BBM-WRP-011-27","price":2699.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023119978878,"sku":"BBM-WRP-011-30","price":2699.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023120011646,"sku":"BBM-WRP-011-40","price":2699.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wet_Room_Lighting_Package_with_a_Recessed_Shower_Light_in_Brushed_Stainless.jpg?v=1789239876"},{"product_id":"wet-room-package-with-coloured-mood-lighting-in-brushed-stainless","title":"Wet Room Package with Coloured Mood Lighting in Brushed Stainless","description":"\u003cp\u003eFor a room that is wet all day: an IP67 RGBW tape in the shower recess on a separate SELV driver, which is the one place colour changing light is not a gimmick.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 16.0 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eCorrosion: 316 marine grade stainless, salt spray tested to 1000 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023120306558,"sku":"BBM-WRP-014-27","price":3249.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023120339326,"sku":"BBM-WRP-014-30","price":3249.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023120372094,"sku":"BBM-WRP-014-40","price":3249.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wet_Room_Package_with_Coloured_Mood_Lighting_in_Brushed_Stainless.jpg?v=1789239877"},{"product_id":"wet-room-lighting-package-with-a-demisting-mirror-in-brushed-stainless","title":"Wet Room Lighting Package with a Demisting Mirror in Brushed Stainless","description":"\u003cp\u003eFor a room that is wet all day: a wet room package with a mirror rated for the humidity a wet room actually reaches, which is not the same specification as a bathroom mirror.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 31.2 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eCorrosion: 316 marine grade stainless, salt spray tested to 1000 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023120699774,"sku":"BBM-WRP-017-27","price":3399.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023120732542,"sku":"BBM-WRP-017-30","price":3399.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023120765310,"sku":"BBM-WRP-017-40","price":3399.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wet_Room_Lighting_Package_with_a_Demisting_Mirror_in_Brushed_Stainless.jpg?v=1789239876"},{"product_id":"sauna-lighting-package-in-brushed-stainless","title":"Sauna Lighting Package in Brushed Stainless","description":"\u003cp\u003eFor a room that is wet all day: fittings rated to 125 degrees with ceramic terminal blocks and no plastic in the hot zone, plus a shielded backrest light.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 14.4 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eCorrosion: 316 marine grade stainless, salt spray tested to 1000 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 125 degrees on the sauna fittings\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023121125758,"sku":"BBM-WRP-020-27","price":3099.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023121158526,"sku":"BBM-WRP-020-30","price":3099.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023121191294,"sku":"BBM-WRP-020-40","price":3099.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Sauna_Lighting_Package_in_Brushed_Stainless.jpg?v=1789239874"},{"product_id":"wet-room-package-for-a-coastal-house-in-brushed-stainless","title":"Wet Room Package for a Coastal House in Brushed Stainless","description":"\u003cp\u003eFor a room that is wet all day: 316 stainless, marine grade gaskets and a salt spray tested finish to BS EN ISO 9227, for a house within a mile of the sea where ordinary chrome pits inside two winters.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 16.3 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eCorrosion: 316 marine grade stainless, salt spray tested to 1000 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023121551742,"sku":"BBM-WRP-023-27","price":3324.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023121584510,"sku":"BBM-WRP-023-30","price":3324.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023121617278,"sku":"BBM-WRP-023-40","price":3324.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wet_Room_Package_for_a_Coastal_House_in_Brushed_Stainless.jpg?v=1789239877"},{"product_id":"wet-room-lighting-package-with-an-extract-system-in-brushed-stainless","title":"Wet Room Lighting Package with an Extract System in Brushed Stainless","description":"\u003cp\u003eFor a room that is wet all day: the lights and a continuous running extract unit specified together, sized to the room volume, because a wet room without proper extract destroys its own ceiling.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by fitting, and every one is listed with its cut out and its overall diameter in the pack list\u003c\/li\u003e\n\u003cli\u003eLight output: 4200 lumens across the package at 86 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, and the SELV circuits dim on the transformer rather than on the mains side, which is what stops a 12 volt fitting flickering at the bottom of the dial\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 2, double insulated, with an integral constant current driver. No earth required and nothing separate to find a home for above the ceiling\u003c\/li\u003e\n\u003cli\u003eFire rating: fire rated to 30, 60 and 90 minutes, tested to BS 476 Part 21 in both plasterboard and timber joist constructions, and the test certificate is downloadable from this page\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked, plus IP testing to BS EN 60529 with a certificate on file\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 23.1 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: seven years on the fitting, the LED module and the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eCorrosion: 316 marine grade stainless, salt spray tested to 1000 hours\u003c\/li\u003e\n\u003cli\u003eGaskets: silicone, captive, and replaceable without removing the fitting\u003c\/li\u003e\n\u003cli\u003eAmbient rating: 45 degrees, which is a wet room specification\u003c\/li\u003e\n\u003cli\u003eDrainage: every recessed fitting is drilled and gasketed so condensate cannot pool on the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eevery fitting in the package\u003c\/li\u003e\n\u003cli\u003ethe SELV transformer where required\u003c\/li\u003e\n\u003cli\u003eIP68 rated gel filled connectors\u003c\/li\u003e\n\u003cli\u003esilicone gaskets and spare gaskets\u003c\/li\u003e\n\u003cli\u003ea zone drawing for your room\u003c\/li\u003e\n\u003cli\u003eIP test certificates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. On a wet room the two things that matter are the transformer position for any SELV circuit, which must be outside the zones, and the gasket seating, which has to be clean and dry when the fitting goes in. A gasket compressed onto a speck of plaster leaks for the rest of its life.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA wet room is not a bathroom with more tiles. The humidity is higher for longer, the fittings are wetted directly rather than splashed, and the corrosion problem is real: 304 stainless, which is what most of the trade sells as stainless, will show orange tea staining within two or three years in a wet room and looks like rust because it is. Everything on this page is 316 or triple plated brass, and we state the salt spray hours rather than the word stainless.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023121912190,"sku":"BBM-WRP-026-27","price":3474.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023121944958,"sku":"BBM-WRP-026-30","price":3474.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023121977726,"sku":"BBM-WRP-026-40","price":3474.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Wet_Room_Lighting_Package_with_an_Extract_System_in_Brushed_Stainless.jpg?v=1789239877"},{"product_id":"ip44-rated-glass-pendant-for-over-a-bath-in-brushed-stainless","title":"IP44 Rated Glass Pendant for Over a Bath in Brushed Stainless","description":"\u003cp\u003eA pendant that is actually rated for a bathroom: a hand blown glass pendant that is actually rated for zone 1, which almost no decorative pendant is, using a sealed lamp holder and a gasketed ceiling rose.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the drop is adjustable from 300 to 1500mm by shortening the flex at the rose\u003c\/li\u003e\n\u003cli\u003eLight output: taking a 6W E14 or E27 LED lamp, supplied, at 806 lumens and 88 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable with the lamp supplied. If you change the lamp, check the replacement is dimmable, because most decorative LED lamps are not\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed ceiling rose and a sealed lamp holder. The earth is not optional on a metal bodied fitting\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 5.4 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eWhy this is rare: a decorative pendant is normally IP20 and unlawful in any bathroom zone. This one is gasketed at the rose, at the holder and at the glass, which is why it costs what it costs\u003c\/li\u003e\n\u003cli\u003eMinimum height: 2.25 metres above the floor if it is over a bath, which is the top of zone 1 and where the rules change\u003c\/li\u003e\n\u003cli\u003eLamp: supplied, dimmable, and replaceable without breaking the seal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe pendant, assembled\u003c\/li\u003e\n\u003cli\u003ethe gasketed ceiling rose and gaskets\u003c\/li\u003e\n\u003cli\u003ethe LED lamp\u003c\/li\u003e\n\u003cli\u003efixings for a ceiling rose or a joist\u003c\/li\u003e\n\u003cli\u003einstallation instructions with the zone diagram\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The rose is gasketed to the ceiling and the gasket has to sit on a flat, clean surface, so if the ceiling is textured it needs skimming flat under the rose. Set the drop before the final connection, because shortening a flex afterwards means breaking the seal.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAlmost every decorative pendant sold for a bathroom is IP20 and is therefore not lawful anywhere in zone 1 or zone 2, which is most of a normal bathroom. The retailers rarely say so and the photographs always show them over a bath. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for. Everything on this page is gasketed and rated, and the zone is stated at the top of the specification rather than in a footnote.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023142130046,"sku":"BBM-PEN-004-27","price":1624.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023142162814,"sku":"BBM-PEN-004-30","price":1624.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023142195582,"sku":"BBM-PEN-004-40","price":1624.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP44_Rated_Glass_Pendant_for_Over_a_Bath_in_Brushed_Stainless.jpg?v=1789239812"},{"product_id":"ip44-rated-crystal-chandelier-for-a-bathroom-in-brushed-stainless","title":"IP44 Rated Crystal Chandelier for a Bathroom in Brushed Stainless","description":"\u003cp\u003eA pendant that is actually rated for a bathroom: a small chandelier rated for zone 2, with sealed holders and a stainless canopy, for the bathroom that is trying to be a room.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the drop is adjustable from 300 to 1500mm by shortening the flex at the rose\u003c\/li\u003e\n\u003cli\u003eLight output: taking a 6W E14 or E27 LED lamp, supplied, at 806 lumens and 88 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable with the lamp supplied. If you change the lamp, check the replacement is dimmable, because most decorative LED lamps are not\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed ceiling rose and a sealed lamp holder. The earth is not optional on a metal bodied fitting\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 14.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eWhy this is rare: a decorative pendant is normally IP20 and unlawful in any bathroom zone. This one is gasketed at the rose, at the holder and at the glass, which is why it costs what it costs\u003c\/li\u003e\n\u003cli\u003eMinimum height: 2.25 metres above the floor if it is over a bath, which is the top of zone 1 and where the rules change\u003c\/li\u003e\n\u003cli\u003eLamp: supplied, dimmable, and replaceable without breaking the seal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe pendant, assembled\u003c\/li\u003e\n\u003cli\u003ethe gasketed ceiling rose and gaskets\u003c\/li\u003e\n\u003cli\u003ethe LED lamp\u003c\/li\u003e\n\u003cli\u003efixings for a ceiling rose or a joist\u003c\/li\u003e\n\u003cli\u003einstallation instructions with the zone diagram\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The rose is gasketed to the ceiling and the gasket has to sit on a flat, clean surface, so if the ceiling is textured it needs skimming flat under the rose. Set the drop before the final connection, because shortening a flex afterwards means breaking the seal.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAlmost every decorative pendant sold for a bathroom is IP20 and is therefore not lawful anywhere in zone 1 or zone 2, which is most of a normal bathroom. The retailers rarely say so and the photographs always show them over a bath. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for. Everything on this page is gasketed and rated, and the zone is stated at the top of the specification rather than in a footnote.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023142523262,"sku":"BBM-PEN-008-27","price":2924.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023142556030,"sku":"BBM-PEN-008-30","price":2924.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023142588798,"sku":"BBM-PEN-008-40","price":2924.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP44_Rated_Crystal_Chandelier_for_a_Bathroom_in_Brushed_Stainless.jpg?v=1789239814"},{"product_id":"ip65-rated-pendant-cluster-for-over-a-bath-in-brushed-stainless","title":"IP65 Rated Pendant Cluster for Over a Bath in Brushed Stainless","description":"\u003cp\u003eA pendant that is actually rated for a bathroom: three pendants at staggered drops on one gasketed rose, wired as one point.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the drop is adjustable from 300 to 1500mm by shortening the flex at the rose\u003c\/li\u003e\n\u003cli\u003eLight output: taking a 6W E14 or E27 LED lamp, supplied, at 806 lumens and 88 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable with the lamp supplied. If you change the lamp, check the replacement is dimmable, because most decorative LED lamps are not\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed ceiling rose and a sealed lamp holder. The earth is not optional on a metal bodied fitting\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 9.7 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eWhy this is rare: a decorative pendant is normally IP20 and unlawful in any bathroom zone. This one is gasketed at the rose, at the holder and at the glass, which is why it costs what it costs\u003c\/li\u003e\n\u003cli\u003eMinimum height: 2.25 metres above the floor if it is over a bath, which is the top of zone 1 and where the rules change\u003c\/li\u003e\n\u003cli\u003eLamp: supplied, dimmable, and replaceable without breaking the seal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe pendant, assembled\u003c\/li\u003e\n\u003cli\u003ethe gasketed ceiling rose and gaskets\u003c\/li\u003e\n\u003cli\u003ethe LED lamp\u003c\/li\u003e\n\u003cli\u003efixings for a ceiling rose or a joist\u003c\/li\u003e\n\u003cli\u003einstallation instructions with the zone diagram\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The rose is gasketed to the ceiling and the gasket has to sit on a flat, clean surface, so if the ceiling is textured it needs skimming flat under the rose. Set the drop before the final connection, because shortening a flex afterwards means breaking the seal.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAlmost every decorative pendant sold for a bathroom is IP20 and is therefore not lawful anywhere in zone 1 or zone 2, which is most of a normal bathroom. The retailers rarely say so and the photographs always show them over a bath. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for. Everything on this page is gasketed and rated, and the zone is stated at the top of the specification rather than in a footnote.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023143637374,"sku":"BBM-PEN-012-27","price":2474.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023143670142,"sku":"BBM-PEN-012-30","price":2474.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023143702910,"sku":"BBM-PEN-012-40","price":2474.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP65_Rated_Pendant_Cluster_for_Over_a_Bath_in_Brushed_Stainless.jpg?v=1789239862"},{"product_id":"ip44-rated-opal-globe-pendant-in-brushed-stainless","title":"IP44 Rated Opal Globe Pendant in Brushed Stainless","description":"\u003cp\u003eA pendant that is actually rated for a bathroom: a 300mm opal globe, which throws light in every direction and is the least glaring thing you can hang over a bath.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the drop is adjustable from 300 to 1500mm by shortening the flex at the rose\u003c\/li\u003e\n\u003cli\u003eLight output: taking a 6W E14 or E27 LED lamp, supplied, at 806 lumens and 88 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable with the lamp supplied. If you change the lamp, check the replacement is dimmable, because most decorative LED lamps are not\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed ceiling rose and a sealed lamp holder. The earth is not optional on a metal bodied fitting\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.4 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eWhy this is rare: a decorative pendant is normally IP20 and unlawful in any bathroom zone. This one is gasketed at the rose, at the holder and at the glass, which is why it costs what it costs\u003c\/li\u003e\n\u003cli\u003eMinimum height: 2.25 metres above the floor if it is over a bath, which is the top of zone 1 and where the rules change\u003c\/li\u003e\n\u003cli\u003eLamp: supplied, dimmable, and replaceable without breaking the seal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe pendant, assembled\u003c\/li\u003e\n\u003cli\u003ethe gasketed ceiling rose and gaskets\u003c\/li\u003e\n\u003cli\u003ethe LED lamp\u003c\/li\u003e\n\u003cli\u003efixings for a ceiling rose or a joist\u003c\/li\u003e\n\u003cli\u003einstallation instructions with the zone diagram\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The rose is gasketed to the ceiling and the gasket has to sit on a flat, clean surface, so if the ceiling is textured it needs skimming flat under the rose. Set the drop before the final connection, because shortening a flex afterwards means breaking the seal.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAlmost every decorative pendant sold for a bathroom is IP20 and is therefore not lawful anywhere in zone 1 or zone 2, which is most of a normal bathroom. The retailers rarely say so and the photographs always show them over a bath. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for. Everything on this page is gasketed and rated, and the zone is stated at the top of the specification rather than in a footnote.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023144030590,"sku":"BBM-PEN-016-27","price":1699.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023144063358,"sku":"BBM-PEN-016-30","price":1699.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023144096126,"sku":"BBM-PEN-016-40","price":1699.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP44_Rated_Opal_Globe_Pendant_in_Brushed_Stainless.jpg?v=1789239803"},{"product_id":"ip44-rated-ribbed-glass-pendant-pair-in-brushed-stainless","title":"IP44 Rated Ribbed Glass Pendant Pair in Brushed Stainless","description":"\u003cp\u003eA pendant that is actually rated for a bathroom: a matched pair for either side of a mirror, hung at 1600mm to the centre of the glass, which is the height that lights a face.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the drop is adjustable from 300 to 1500mm by shortening the flex at the rose\u003c\/li\u003e\n\u003cli\u003eLight output: taking a 6W E14 or E27 LED lamp, supplied, at 806 lumens and 88 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable with the lamp supplied. If you change the lamp, check the replacement is dimmable, because most decorative LED lamps are not\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed ceiling rose and a sealed lamp holder. The earth is not optional on a metal bodied fitting\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 9.0 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eWhy this is rare: a decorative pendant is normally IP20 and unlawful in any bathroom zone. This one is gasketed at the rose, at the holder and at the glass, which is why it costs what it costs\u003c\/li\u003e\n\u003cli\u003eMinimum height: 2.25 metres above the floor if it is over a bath, which is the top of zone 1 and where the rules change\u003c\/li\u003e\n\u003cli\u003eLamp: supplied, dimmable, and replaceable without breaking the seal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe pendant, assembled\u003c\/li\u003e\n\u003cli\u003ethe gasketed ceiling rose and gaskets\u003c\/li\u003e\n\u003cli\u003ethe LED lamp\u003c\/li\u003e\n\u003cli\u003efixings for a ceiling rose or a joist\u003c\/li\u003e\n\u003cli\u003einstallation instructions with the zone diagram\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The rose is gasketed to the ceiling and the gasket has to sit on a flat, clean surface, so if the ceiling is textured it needs skimming flat under the rose. Set the drop before the final connection, because shortening a flex afterwards means breaking the seal.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAlmost every decorative pendant sold for a bathroom is IP20 and is therefore not lawful anywhere in zone 1 or zone 2, which is most of a normal bathroom. The retailers rarely say so and the photographs always show them over a bath. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for. Everything on this page is gasketed and rated, and the zone is stated at the top of the specification rather than in a footnote.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023144915326,"sku":"BBM-PEN-020-27","price":2074.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023144948094,"sku":"BBM-PEN-020-30","price":2074.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023144980862,"sku":"BBM-PEN-020-40","price":2074.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP44_Rated_Ribbed_Glass_Pendant_Pair_in_Brushed_Stainless.jpg?v=1789239812"},{"product_id":"ip65-rated-pendant-for-a-wet-room-in-brushed-stainless","title":"IP65 Rated Pendant for a Wet Room in Brushed Stainless","description":"\u003cp\u003eA pendant that is actually rated for a bathroom: 316 stainless and a bonded glass, rated for zone 1 in a room that is wet all day.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the drop is adjustable from 300 to 1500mm by shortening the flex at the rose\u003c\/li\u003e\n\u003cli\u003eLight output: taking a 6W E14 or E27 LED lamp, supplied, at 806 lumens and 88 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable with the lamp supplied. If you change the lamp, check the replacement is dimmable, because most decorative LED lamps are not\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed ceiling rose and a sealed lamp holder. The earth is not optional on a metal bodied fitting\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 8.7 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eWhy this is rare: a decorative pendant is normally IP20 and unlawful in any bathroom zone. This one is gasketed at the rose, at the holder and at the glass, which is why it costs what it costs\u003c\/li\u003e\n\u003cli\u003eMinimum height: 2.25 metres above the floor if it is over a bath, which is the top of zone 1 and where the rules change\u003c\/li\u003e\n\u003cli\u003eLamp: supplied, dimmable, and replaceable without breaking the seal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe pendant, assembled\u003c\/li\u003e\n\u003cli\u003ethe gasketed ceiling rose and gaskets\u003c\/li\u003e\n\u003cli\u003ethe LED lamp\u003c\/li\u003e\n\u003cli\u003efixings for a ceiling rose or a joist\u003c\/li\u003e\n\u003cli\u003einstallation instructions with the zone diagram\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The rose is gasketed to the ceiling and the gasket has to sit on a flat, clean surface, so if the ceiling is textured it needs skimming flat under the rose. Set the drop before the final connection, because shortening a flex afterwards means breaking the seal.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAlmost every decorative pendant sold for a bathroom is IP20 and is therefore not lawful anywhere in zone 1 or zone 2, which is most of a normal bathroom. The retailers rarely say so and the photographs always show them over a bath. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for. Everything on this page is gasketed and rated, and the zone is stated at the top of the specification rather than in a footnote.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023145832830,"sku":"BBM-PEN-028-27","price":2699.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023145865598,"sku":"BBM-PEN-028-30","price":2699.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023145898366,"sku":"BBM-PEN-028-40","price":2699.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP65_Rated_Pendant_for_a_Wet_Room_in_Brushed_Stainless.jpg?v=1789239875"},{"product_id":"ip44-rated-alabaster-pendant-in-brushed-stainless","title":"IP44 Rated Alabaster Pendant in Brushed Stainless","description":"\u003cp\u003eA pendant that is actually rated for a bathroom: hand carved alabaster, sealed against humidity, which is a stone that behaves badly in a bathroom unless it is properly finished and beautifully when it is.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the drop is adjustable from 300 to 1500mm by shortening the flex at the rose\u003c\/li\u003e\n\u003cli\u003eLight output: taking a 6W E14 or E27 LED lamp, supplied, at 806 lumens and 88 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable with the lamp supplied. If you change the lamp, check the replacement is dimmable, because most decorative LED lamps are not\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed ceiling rose and a sealed lamp holder. The earth is not optional on a metal bodied fitting\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 13.7 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eWhy this is rare: a decorative pendant is normally IP20 and unlawful in any bathroom zone. This one is gasketed at the rose, at the holder and at the glass, which is why it costs what it costs\u003c\/li\u003e\n\u003cli\u003eMinimum height: 2.25 metres above the floor if it is over a bath, which is the top of zone 1 and where the rules change\u003c\/li\u003e\n\u003cli\u003eLamp: supplied, dimmable, and replaceable without breaking the seal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe pendant, assembled\u003c\/li\u003e\n\u003cli\u003ethe gasketed ceiling rose and gaskets\u003c\/li\u003e\n\u003cli\u003ethe LED lamp\u003c\/li\u003e\n\u003cli\u003efixings for a ceiling rose or a joist\u003c\/li\u003e\n\u003cli\u003einstallation instructions with the zone diagram\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The rose is gasketed to the ceiling and the gasket has to sit on a flat, clean surface, so if the ceiling is textured it needs skimming flat under the rose. Set the drop before the final connection, because shortening a flex afterwards means breaking the seal.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAlmost every decorative pendant sold for a bathroom is IP20 and is therefore not lawful anywhere in zone 1 or zone 2, which is most of a normal bathroom. The retailers rarely say so and the photographs always show them over a bath. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for. Everything on this page is gasketed and rated, and the zone is stated at the top of the specification rather than in a footnote.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023146324350,"sku":"BBM-PEN-032-27","price":3549.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023146357118,"sku":"BBM-PEN-032-30","price":3549.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023146389886,"sku":"BBM-PEN-032-40","price":3549.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP44_Rated_Alabaster_Pendant_in_Brushed_Stainless.jpg?v=1789239802"},{"product_id":"ip44-rated-fluted-glass-pendant-trio-in-brushed-stainless","title":"IP44 Rated Fluted Glass Pendant Trio in Brushed Stainless","description":"\u003cp\u003eA pendant that is actually rated for a bathroom: three fluted cylinders on a linear rose, for a long room or over a double basin.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the drop is adjustable from 300 to 1500mm by shortening the flex at the rose\u003c\/li\u003e\n\u003cli\u003eLight output: taking a 6W E14 or E27 LED lamp, supplied, at 806 lumens and 88 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable with the lamp supplied. If you change the lamp, check the replacement is dimmable, because most decorative LED lamps are not\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed ceiling rose and a sealed lamp holder. The earth is not optional on a metal bodied fitting\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 10.9 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eWhy this is rare: a decorative pendant is normally IP20 and unlawful in any bathroom zone. This one is gasketed at the rose, at the holder and at the glass, which is why it costs what it costs\u003c\/li\u003e\n\u003cli\u003eMinimum height: 2.25 metres above the floor if it is over a bath, which is the top of zone 1 and where the rules change\u003c\/li\u003e\n\u003cli\u003eLamp: supplied, dimmable, and replaceable without breaking the seal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe pendant, assembled\u003c\/li\u003e\n\u003cli\u003ethe gasketed ceiling rose and gaskets\u003c\/li\u003e\n\u003cli\u003ethe LED lamp\u003c\/li\u003e\n\u003cli\u003efixings for a ceiling rose or a joist\u003c\/li\u003e\n\u003cli\u003einstallation instructions with the zone diagram\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The rose is gasketed to the ceiling and the gasket has to sit on a flat, clean surface, so if the ceiling is textured it needs skimming flat under the rose. Set the drop before the final connection, because shortening a flex afterwards means breaking the seal.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAlmost every decorative pendant sold for a bathroom is IP20 and is therefore not lawful anywhere in zone 1 or zone 2, which is most of a normal bathroom. The retailers rarely say so and the photographs always show them over a bath. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for. Everything on this page is gasketed and rated, and the zone is stated at the top of the specification rather than in a footnote.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023146717566,"sku":"BBM-PEN-036-27","price":2549.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023146750334,"sku":"BBM-PEN-036-30","price":2549.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023146783102,"sku":"BBM-PEN-036-40","price":2549.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP44_Rated_Fluted_Glass_Pendant_Trio_in_Brushed_Stainless.jpg?v=1789239812"},{"product_id":"ip44-rated-pendant-with-a-fabric-shade-in-brushed-stainless","title":"IP44 Rated Pendant with a Fabric Shade in Brushed Stainless","description":"\u003cp\u003eA pendant that is actually rated for a bathroom: a moisture resistant fabric shade over a sealed holder, for a bathroom outside the zones where the fitting can be softer.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zone 2 and outside the zones. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a washbasin tap. It is not rated for zone 1, which means not directly over the bath\u003c\/li\u003e\n\u003cli\u003eIP rating: IP44. The first digit, 4, means protected against solid objects over 1mm. The second digit, 4, means protected against splashing water from any direction. It is the minimum for zone 2 and it is not enough for zone 1\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the drop is adjustable from 300 to 1500mm by shortening the flex at the rose\u003c\/li\u003e\n\u003cli\u003eLight output: taking a 6W E14 or E27 LED lamp, supplied, at 806 lumens and 88 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 95, measured, with R9 above 60. R9 is the deep red value and it is the one that decides whether skin looks like skin. Most bathroom fittings quote a CRI in the eighties and do not quote R9 at all, which is how you end up shaving by a light that makes you look ill\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable with the lamp supplied. If you change the lamp, check the replacement is dimmable, because most decorative LED lamps are not\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed ceiling rose and a sealed lamp holder. The earth is not optional on a metal bodied fitting\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 6.8 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: marine grade 316 stainless, not the 304 that most of the trade uses. In a wet room or a coastal house 304 will tea stain within a couple of years and 316 will not\u003c\/li\u003e\n\u003cli\u003eWhy this is rare: a decorative pendant is normally IP20 and unlawful in any bathroom zone. This one is gasketed at the rose, at the holder and at the glass, which is why it costs what it costs\u003c\/li\u003e\n\u003cli\u003eMinimum height: 2.25 metres above the floor if it is over a bath, which is the top of zone 1 and where the rules change\u003c\/li\u003e\n\u003cli\u003eLamp: supplied, dimmable, and replaceable without breaking the seal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe pendant, assembled\u003c\/li\u003e\n\u003cli\u003ethe gasketed ceiling rose and gaskets\u003c\/li\u003e\n\u003cli\u003ethe LED lamp\u003c\/li\u003e\n\u003cli\u003efixings for a ceiling rose or a joist\u003c\/li\u003e\n\u003cli\u003einstallation instructions with the zone diagram\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The rose is gasketed to the ceiling and the gasket has to sit on a flat, clean surface, so if the ceiling is textured it needs skimming flat under the rose. Set the drop before the final connection, because shortening a flex afterwards means breaking the seal.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eAlmost every decorative pendant sold for a bathroom is IP20 and is therefore not lawful anywhere in zone 1 or zone 2, which is most of a normal bathroom. The retailers rarely say so and the photographs always show them over a bath. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for. Everything on this page is gasketed and rated, and the zone is stated at the top of the specification rather than in a footnote.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023147209086,"sku":"BBM-PEN-040-27","price":1774.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023147241854,"sku":"BBM-PEN-040-30","price":1774.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023147274622,"sku":"BBM-PEN-040-40","price":1774.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/IP44_Rated_Pendant_with_a_Fabric_Shade_in_Brushed_Stainless.jpg?v=1789239800"},{"product_id":"marine-grade-ip65-wall-light-in-brushed-chrome","title":"Marine Grade IP65 Wall Light in Brushed Chrome","description":"\u003cp\u003eA wall light for a bathroom: 316 stainless for a wet room or a coastal house.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the projection from the wall is stated on the drawing in the gallery\u003c\/li\u003e\n\u003cli\u003eLight output: 620 lumens at 84 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, trailing edge\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed back plate. A metal bodied fitting in a bathroom is earthed and that is not negotiable\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 2.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: the same triple plate with a directional brush, which hides limescale spotting far better than polished does and is the sensible choice in a hard water area\u003c\/li\u003e\n\u003cli\u003eHeight: 1600mm to centre if it is beside a mirror, which puts the source at face height and is the reason wall lights beat downlights at a basin\u003c\/li\u003e\n\u003cli\u003eGasket: silicone at the back plate, and the wall under it needs to be flat\u003c\/li\u003e\n\u003cli\u003eGlass: moulded and toughened\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe fitting\u003c\/li\u003e\n\u003cli\u003ethe gasketed back plate\u003c\/li\u003e\n\u003cli\u003efixings for tile and plasterboard\u003c\/li\u003e\n\u003cli\u003ea drilling template\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The back plate gasket needs a flat clean surface, so on a tiled wall it should sit on whole tiles rather than across a grout line where it can.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA pair of wall lights at face height either side of a mirror is the best lighting a bathroom can have, and it costs less than the six downlights that usually get fitted instead. The catch is that it has to be decided before the tiling, because two cables at 1600mm on a tiled wall are not a retrofit. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023169327486,"sku":"BBM-WAL-031-27","price":209.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023169360254,"sku":"BBM-WAL-031-30","price":209.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023169393022,"sku":"BBM-WAL-031-40","price":209.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Marine_Grade_IP65_Wall_Light_in_Brushed_Chrome.jpg?v=1789239860"},{"product_id":"marine-grade-ip65-wall-light-in-matt-black","title":"Marine Grade IP65 Wall Light in Matt Black","description":"\u003cp\u003eA wall light for a bathroom: 316 stainless for a wet room or a coastal house.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the projection from the wall is stated on the drawing in the gallery\u003c\/li\u003e\n\u003cli\u003eLight output: 620 lumens at 84 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, trailing edge\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed back plate. A metal bodied fitting in a bathroom is earthed and that is not negotiable\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 2.6 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: a fine texture matt black powder coat over a chromated primer, because black paint straight onto aluminium in a bathroom lifts at the edges within two years\u003c\/li\u003e\n\u003cli\u003eHeight: 1600mm to centre if it is beside a mirror, which puts the source at face height and is the reason wall lights beat downlights at a basin\u003c\/li\u003e\n\u003cli\u003eGasket: silicone at the back plate, and the wall under it needs to be flat\u003c\/li\u003e\n\u003cli\u003eGlass: moulded and toughened\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe fitting\u003c\/li\u003e\n\u003cli\u003ethe gasketed back plate\u003c\/li\u003e\n\u003cli\u003efixings for tile and plasterboard\u003c\/li\u003e\n\u003cli\u003ea drilling template\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The back plate gasket needs a flat clean surface, so on a tiled wall it should sit on whole tiles rather than across a grout line where it can.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA pair of wall lights at face height either side of a mirror is the best lighting a bathroom can have, and it costs less than the six downlights that usually get fitted instead. The catch is that it has to be decided before the tiling, because two cables at 1600mm on a tiled wall are not a retrofit. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023169425790,"sku":"BBM-WAL-032-27","price":219.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023169458558,"sku":"BBM-WAL-032-30","price":219.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023169491326,"sku":"BBM-WAL-032-40","price":219.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Marine_Grade_IP65_Wall_Light_in_Matt_Black.jpg?v=1789239869"},{"product_id":"marine-grade-ip65-wall-light-in-brushed-brass","title":"Marine Grade IP65 Wall Light in Brushed Brass","description":"\u003cp\u003eA wall light for a bathroom: 316 stainless for a wet room or a coastal house.\u003c\/p\u003e\u003cp\u003eBathroom lighting is the one part of a house where getting it wrong is a safety matter rather than a taste matter, and it is sold almost entirely on photographs. Every listing here states the zone the fitting may be installed in, the IP rating with both digits explained, the colour rendering index, the lumen output and the efficacy in lumens per circuit watt. If a fitting is not suitable above a bath we say so on the page you are buying it from. If a mirror is backlit and will not light your face, we say that too.\u003c\/p\u003e\u003ch3\u003eSpecification\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eZone: zones 1 and 2. Zone 1 is directly above the bath or the shower tray up to 2.25 metres from the floor, and this fitting is rated for it\u003c\/li\u003e\n\u003cli\u003eIP rating: IP65. Dust tight, and protected against low pressure water jets from any direction. This is the rating for zone 1, which is directly above a bath or in a shower\u003c\/li\u003e\n\u003cli\u003eDimensions: varies by model, and the projection from the wall is stated on the drawing in the gallery\u003c\/li\u003e\n\u003cli\u003eLight output: 620 lumens at 84 lumens per circuit watt\u003c\/li\u003e\n\u003cli\u003eColour temperature: chosen above\u003c\/li\u003e\n\u003cli\u003eColour rendering: CRI 90, with R9 above 50, which is a good deal better than the eighties that this category usually offers and is enough for everything except colour matching makeup\u003c\/li\u003e\n\u003cli\u003eDimming: mains dimmable, trailing edge\u003c\/li\u003e\n\u003cli\u003eElectrical: Class 1, earthed, with a gasketed back plate. A metal bodied fitting in a bathroom is earthed and that is not negotiable\u003c\/li\u003e\n\u003cli\u003eFire rating: not applicable to a wall or surface mounted fitting\u003c\/li\u003e\n\u003cli\u003eStandards: BS EN 60598 for luminaires, BS EN 62471 photobiological safety at the exempt group, BS EN 55015 for electromagnetic emissions, UKCA and CE marked\u003c\/li\u003e\n\u003cli\u003eWeight: approximately 2.8 kilograms\u003c\/li\u003e\n\u003cli\u003eGuarantee: five years on the fitting and the LED module, two years on the driver\u003c\/li\u003e\n\u003cli\u003eFinish: unlacquered brushed brass, which will patinate in a bathroom and is meant to. If you want it to stay bright, buy the chrome\u003c\/li\u003e\n\u003cli\u003eHeight: 1600mm to centre if it is beside a mirror, which puts the source at face height and is the reason wall lights beat downlights at a basin\u003c\/li\u003e\n\u003cli\u003eGasket: silicone at the back plate, and the wall under it needs to be flat\u003c\/li\u003e\n\u003cli\u003eGlass: moulded and toughened\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ethe fitting\u003c\/li\u003e\n\u003cli\u003ethe gasketed back plate\u003c\/li\u003e\n\u003cli\u003efixings for tile and plasterboard\u003c\/li\u003e\n\u003cli\u003ea drilling template\u003c\/li\u003e\n\u003cli\u003einstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cp\u003eA registered electrician. Electrical work in a room containing a bath or a shower is notifiable under Part P of the Building Regulations in England and Wales. That means it has to be done by a registered electrician or signed off by building control. Replacing a like for like fitting on an existing circuit is not notifiable. Adding a new circuit, a new socket or a new spur is. The back plate gasket needs a flat clean surface, so on a tiled wall it should sit on whole tiles rather than across a grout line where it can.\u003c\/p\u003e\u003ch3\u003eChoosing between this and the alternatives\u003c\/h3\u003e\u003cp\u003eA pair of wall lights at face height either side of a mirror is the best lighting a bathroom can have, and it costs less than the six downlights that usually get fitted instead. The catch is that it has to be decided before the tiling, because two cables at 1600mm on a tiled wall are not a retrofit. The zones come from BS 7671, the IET Wiring Regulations. Zone 0 is inside the bath or shower tray. Zone 1 is above it to 2.25 metres. Zone 2 is the 600mm band beyond zone 1 and the 600mm radius around a basin tap. Outside those, the regulations impose no IP requirement, though a bathroom is still a bathroom and steam still rises. Every product page here states which zones the fitting is rated for.\u003c\/p\u003e","brand":"Bathe and Beam","offers":[{"title":"2700K warm white","offer_id":58023169524094,"sku":"BBM-WAL-033-27","price":269.0,"currency_code":"GBP","in_stock":true},{"title":"3000K warm white","offer_id":58023169556862,"sku":"BBM-WAL-033-30","price":269.0,"currency_code":"GBP","in_stock":true},{"title":"4000K neutral white","offer_id":58023169589630,"sku":"BBM-WAL-033-40","price":269.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/1527\/9230\/files\/Marine_Grade_IP65_Wall_Light_in_Brushed_Brass.jpg?v=1789239876"}],"url":"https:\/\/batheandbeam.com\/collections\/316-stainless.oembed","provider":"Bathe \u0026 Beam","version":"1.0","type":"link"}